VND14NV04-E
| Parameters | |
|---|---|
| Factory Lead Time | 20 Weeks |
| Lifecycle Status | ACTIVE (Last Updated: 7 months ago) |
| Mount | Surface Mount |
| Mounting Type | Surface Mount |
| Package / Case | TO-252-3, DPak (2 Leads + Tab), SC-63 |
| Number of Pins | 3 |
| Operating Temperature | -40°C~150°C TJ |
| Packaging | Tube |
| Series | OMNIFET II™, VIPower™ |
| JESD-609 Code | e3 |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 3 (168 Hours) |
| Number of Terminations | 2 |
| ECCN Code | EAR99 |
| Resistance | 35mOhm |
| Terminal Finish | Tin (Sn) |
| Max Power Dissipation | 74W |
| Terminal Position | SINGLE |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 260 |
| Number of Functions | 1 |
| Terminal Pitch | 2.25mm |
| Time@Peak Reflow Temperature-Max (s) | 30 |
| Base Part Number | VND14 |
| Pin Count | 3 |
| JESD-30 Code | R-PSSO-G2 |
| Output Type | N-Channel |
| Max Output Current | 12A |
| Interface | On/Off |
| Nominal Supply Current | 100μA |
| Output Configuration | Low Side |
| Power Dissipation | 74W |
| Output Current | 18A |
| Voltage - Supply (Vcc/Vdd) | Not Required |
| Max Supply Current | 100μA |
| Input Type | Non-Inverting |
| Turn On Delay Time | 1.5 μs |
| Switch Type | General Purpose |
| Rise Time | 9.7μs |
| Drain to Source Voltage (Vdss) | 55V |
| Fall Time (Typ) | 10.2 μs |
| Turn-Off Delay Time | 25 μs |
| Continuous Drain Current (ID) | 7A |
| Threshold Voltage | 2.5V |
| Ratio - Input:Output | 1:1 |
| Voltage - Load | 36V Max |
| Fault Protection | Current Limiting (Fixed), Over Temperature, Over Voltage |
| Drain to Source Breakdown Voltage | 40V |
| Number of Drivers | 1 |
| Turn On Time | 4.5 μs |
| Output Peak Current Limit-Nom | 18A |
| Rds On (Typ) | 35m Ω (Max) |
| Drain to Source Resistance | 35mOhm |
| Built-in Protections | TRANSIENT; OVER CURRENT; OVER VOLTAGE; THERMAL |
| Height | 2.63mm |
| Length | 6.6mm |
| Width | 6.2mm |
| Radiation Hardening | No |
| REACH SVHC | No SVHC |
| RoHS Status | ROHS3 Compliant |
| Lead Free | Lead Free |
VND14NV04-E Overview
It's?packaged?in?the way?of?a?Tube.It's included in the TO-252-3, DPak (2 Leads + Tab), SC-63 package.The mounting type of the LED driver is Surface Mount.There is a switch type of General Purpose.In order to guarantee reliable performance, the temperature should be set to -40°C~150°C TJ.With a supply voltage of Not Required, the LED driving board operates.A maximum voltage of N-Channel volts is available from the output of this LED driver.As you can see, it comes from the VND14 family.A total of 2 terminations have been found in it.During operation, the 3 pins are used.It is important to note that the LED driving board has 1 functions.Maximum output current falls to 12A when operation criteria are met.The LED driving board is mounted in the way of Surface Mount.The LED driving board is equipped with a total of 3 pins.It has a resistance of 35mOhm.It is part of the OMNIFET II?, VIPower? series.It is set to 18A in this case.A maximum current requirement of 100μA is required for its operation.The part has 1 drivers.
VND14NV04-E Features
Resistance of 35mOhm
VND14NV04-E Applications
There are a lot of STMicroelectronics VND14NV04-E Power Switches ICs applications.
- Handheld Devices
- USB Power Distribution
- Storage (HDDs, SSDs)
- Wireless Headsets
- Set-top-box
- Portable GPS
- Smart Phones, Feature Phones
- Portable/Handheld Devices
- Hot-Swap Systems
- Hard Disk Drives