TLV274ID
| Parameters | |
|---|---|
| Factory Lead Time | 6 Weeks |
| Lifecycle Status | ACTIVE (Last Updated: 2 days ago) |
| Mounting Type | Surface Mount |
| Package / Case | 14-SOIC (0.154, 3.90mm Width) |
| Surface Mount | YES |
| Number of Pins | 14 |
| Operating Temperature | -40°C~125°C |
| Packaging | Tube |
| JESD-609 Code | e4 |
| Pbfree Code | yes |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 14 |
| ECCN Code | EAR99 |
| Terminal Finish | Nickel/Palladium/Gold (Ni/Pd/Au) |
| Subcategory | Operational Amplifier |
| Technology | CMOS |
| Terminal Position | DUAL |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 260 |
| Number of Functions | 4 |
| Supply Voltage | 5V |
| Terminal Pitch | 1.27mm |
| Base Part Number | TLV274 |
| Pin Count | 14 |
| Output Type | Rail-to-Rail |
| Operating Supply Voltage | 5V |
| Power Supplies | +-1.35/+-8/2.7/16V |
| Number of Channels | 4 |
| Operating Supply Current | 625μA |
| Nominal Supply Current | 3.2mA |
| Power Dissipation | 531mW |
| Output Current | 13mA |
| Slew Rate | 2.6V/μs |
| Architecture | VOLTAGE-FEEDBACK |
| Amplifier Type | General Purpose |
| Common Mode Rejection Ratio | 69 dB |
| Current - Input Bias | 1pA |
| Voltage - Supply, Single/Dual (±) | 2.7V~16V ±1.35V~8V |
| Output Current per Channel | 13mA |
| Input Offset Voltage (Vos) | 5mV |
| Bandwidth | 3MHz |
| Neg Supply Voltage-Nom (Vsup) | -5V |
| Unity Gain BW-Nom | 3000 kHz |
| Voltage Gain | 110dB |
| Average Bias Current-Max (IIB) | 0.00006μA |
| Power Supply Rejection Ratio (PSRR) | 70dB |
| Low-Offset | NO |
| Frequency Compensation | YES |
| Voltage - Input Offset | 500μV |
| Current - Output / Channel | 8mA |
| Low-Bias | YES |
| Micropower | NO |
| Bias Current-Max (IIB) @25C | 0.00006μA |
| Programmable Power | NO |
| Dual Supply Voltage | 5V |
| Nominal Gain Bandwidth Product | 3MHz |
| Max I/O Voltage | 5mV |
| Input Offset Current-Max (IIO) | 0.00006μA |
| Height | 1.75mm |
| Length | 8.65mm |
| Width | 3.91mm |
| Thickness | 1.58mm |
| Radiation Hardening | No |
| REACH SVHC | No SVHC |
| RoHS Status | ROHS3 Compliant |
| Lead Free | Lead Free |
TLV274ID Overview
There is a 14-SOIC (0.154, 3.90mm Width) case package that contains the instrumentation amplifiers. The instrumentation amplifier in this picture is of the General Purpose-type. A Tube case is used for delivering the op amp. There have been a total of 14 terminations over the past year. Buffer amplifier has a total of 14 pins on it. It would be helpful if you could remember that this op amp ic should be powered by an 5V battery. In more specific terms, this linear amplifier can be categoriOperational Amplifiered as a Operational Amplifier-type device. 14 pins are located on the operational amplifiers. Op amp rates 5mV as input offset voltage. This electrical part should be mounted using type Surface Mount. In relation to the operating temperature of this buffer op amp, it works well at an average of -40°C~125°C . You can run this op amp ic on 625μA . There should be no change in the voltage gain at 110dB. As far as the device is concerned, buffer amplifier has 4 channels. One of its many advantages is that buffer op amp outputs Rail-to-Rail signals. The operating supply voltage of instrumentation amplifier is rated 5V voltage.
TLV274ID Features
14 Pins
supply voltage of 5V
110dB voltage gain
Output Type: Rail-to-Rail
TLV274ID Applications
There are a lot of Texas Instruments TLV274ID Instrumentational OP Amps applications.
- PDA
- Industrial applications including automation
- Power transmission
- Gaming industry
- Portable electronic products powered by batteries
- High speed sample
- Power control
- Band-stop filter
- Non-polarized electrodes
- Automation control systems