TLV271IP
| Parameters | |
|---|---|
| Factory Lead Time | 6 Weeks |
| Lifecycle Status | ACTIVE (Last Updated: 4 days ago) |
| Mounting Type | Through Hole |
| Package / Case | 8-DIP (0.300, 7.62mm) |
| Surface Mount | NO |
| Number of Pins | 8 |
| Operating Temperature | -40°C~125°C |
| Packaging | Tube |
| JESD-609 Code | e4 |
| Pbfree Code | yes |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 8 |
| ECCN Code | EAR99 |
| Terminal Finish | Nickel/Palladium/Gold (Ni/Pd/Au) |
| Subcategory | Operational Amplifier |
| Terminal Position | DUAL |
| Number of Functions | 1 |
| Supply Voltage | 5V |
| Terminal Pitch | 2.54mm |
| Base Part Number | TLV271 |
| Pin Count | 8 |
| Output Type | Rail-to-Rail |
| Operating Supply Voltage | 5V |
| Number of Channels | 1 |
| Operating Supply Current | 625μA |
| Nominal Supply Current | 800μA |
| Power Dissipation | 625mW |
| Output Current | 13mA |
| Slew Rate | 2.6V/μs |
| Architecture | VOLTAGE-FEEDBACK |
| Amplifier Type | CMOS |
| Common Mode Rejection Ratio | 69 dB |
| Current - Input Bias | 1pA |
| Voltage - Supply, Single/Dual (±) | 2.7V~16V ±1.35V~8V |
| Output Current per Channel | 13mA |
| Input Offset Voltage (Vos) | 5mV |
| Bandwidth | 3MHz |
| Neg Supply Voltage-Nom (Vsup) | -5V |
| Unity Gain BW-Nom | 3000 kHz |
| Voltage Gain | 110dB |
| Average Bias Current-Max (IIB) | 0.00006μA |
| Power Supply Rejection Ratio (PSRR) | 70dB |
| Low-Offset | NO |
| Frequency Compensation | YES |
| Voltage - Input Offset | 500μV |
| Current - Output / Channel | 8mA |
| Low-Bias | YES |
| Micropower | NO |
| Bias Current-Max (IIB) @25C | 0.00006μA |
| Programmable Power | NO |
| Dual Supply Voltage | 5V |
| Nominal Gain Bandwidth Product | 3MHz |
| Max I/O Voltage | 5mV |
| Input Offset Current-Max (IIO) | 0.00006μA |
| Height | 5.08mm |
| Length | 9.81mm |
| Width | 6.35mm |
| Thickness | 3.9mm |
| Radiation Hardening | No |
| REACH SVHC | No SVHC |
| RoHS Status | ROHS3 Compliant |
| Lead Free | Lead Free |
TLV271IP Overview
A 8-DIP (0.300, 7.62mm) case is used to package the op amp. The instrumentation amplifier in this picture is of the CMOS-type. As far as the packaging is concerned, buffer op amp is delivered in a Tube case. In recent months, the number of terminations has approached 8. Linear amplifier has a total of 8 pins. It is important to remember that this op amp should be operated at a voltage of 5V volts. It should be noted that this op amp is a type of Operational Amplifier device. 8 pins are included on the operational amplifiers. With regard to input offset voltage, instrumentation amplifier is rated at 5mV. Through Hole is the recommended mounting type of operational amplifiers. In terms of operating temperature, this instrumentation amplifier performs well at a temperature of about -40°C~125°C . You can run this op amp ic on 625μA . You should keep the voltage gain at 110dB for the time being. Instrumentation amplifier has 1 channels on it. One of the advantages of this op amp is that it outputs Rail-to-Rail signals, which is one of its many advantages. The operating supply voltage of instrumentation amplifier is rated 5V voltage.
TLV271IP Features
8 Pins
supply voltage of 5V
110dB voltage gain
Output Type: Rail-to-Rail
TLV271IP Applications
There are a lot of Texas Instruments TLV271IP Instrumentational OP Amps applications.
- Differentiator circuits
- Mobile phone
- Signal amplification
- Image computer boards
- Inverse/same-phase proportional circuit
- Automatic control
- Fission chambers
- Portable electronic products powered by batteries
- Digital cameras
- Displayers for aircraft and air transportation control systems