TL062IP
| Parameters | |
|---|---|
| Factory Lead Time | 6 Weeks |
| Lifecycle Status | ACTIVE (Last Updated: 4 days ago) |
| Mounting Type | Through Hole |
| Package / Case | 8-DIP (0.300, 7.62mm) |
| Surface Mount | NO |
| Number of Pins | 8 |
| Operating Temperature | -40°C~85°C |
| Packaging | Tube |
| JESD-609 Code | e4 |
| Pbfree Code | yes |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 8 |
| ECCN Code | EAR99 |
| Terminal Finish | Nickel/Palladium/Gold (Ni/Pd/Au) |
| Subcategory | Operational Amplifier |
| Technology | BIPOLAR |
| Terminal Position | DUAL |
| Peak Reflow Temperature (Cel) | 260 |
| Number of Functions | 2 |
| Supply Voltage | 15V |
| Base Part Number | TL062 |
| Pin Count | 8 |
| Operating Supply Voltage | 18V |
| Power Supplies | +-15V |
| Number of Channels | 2 |
| Operating Supply Current | 200μA |
| Nominal Supply Current | 500μA |
| Max Supply Current | 500μA |
| Slew Rate | 3.5V/μs |
| Architecture | VOLTAGE-FEEDBACK |
| Amplifier Type | J-FET |
| Common Mode Rejection Ratio | 80 dB |
| Current - Input Bias | 30pA |
| Voltage - Supply, Single/Dual (±) | 7V~36V ±3.5V~18V |
| Input Offset Voltage (Vos) | 3mV |
| Bandwidth | 1MHz |
| Neg Supply Voltage-Nom (Vsup) | -15V |
| Unity Gain BW-Nom | 1000 kHz |
| Voltage Gain | 75.56dB |
| Low-Offset | NO |
| Frequency Compensation | YES |
| Low-Bias | YES |
| Micropower | YES |
| Programmable Power | NO |
| Dual Supply Voltage | 9V |
| Nominal Gain Bandwidth Product | 1MHz |
| Max I/O Voltage | 6mV |
| Input Offset Current-Max (IIO) | 0.0001μA |
| Height | 5.08mm |
| Length | 9.81mm |
| Width | 6.35mm |
| Thickness | 3.9mm |
| Radiation Hardening | No |
| REACH SVHC | No SVHC |
| RoHS Status | ROHS3 Compliant |
| Lead Free | Lead Free |
TL062IP Overview
In the package, you will find a 8-DIP (0.300, 7.62mm)-case to contain the op amp ic. The instrumentation amplifier in this picture is of the J-FET-type. In the case of Tube cases, linear amplifier will be delivered. There have been a total of 8 terminations over the past year. It consists of a total of 8 pins in total. As a reminder, this buffer op amp should be powered by 15V battery and that the battery should be inserted in the amplifier. It should be noted that this type of buffer amplifier is exactly what is known as a Operational Amplifier device. 8 pins are located on the operational amplifiers. In terms of input offset voltage, operational amplifier rates 3mV. For this electronic part, it is recommended that you mount it with type Through Hole. In terms of operating temperatures, this buffer amplifier works very well at a temperature of around -40°C~85°C . In order for this instrumentation amplifier to operate, the supply current needs to be between 200μA and 10 . 75.56dB should remain the voltage gain. Buffer op amp is equipped with 2 channels on the device. The operating supply voltage of the buffer op amp is rated at 18V.
TL062IP Features
8 Pins
supply voltage of 15V
75.56dB voltage gain
TL062IP Applications
There are a lot of Texas Instruments TL062IP Instrumentational OP Amps applications.
- Switching amplifier
- Medical instruments
- Weak signal detection
- Fission chambers
- Weighing systems
- Laptop
- Biopotential
- Navigation
- Television broadcasting equipment
- Power control