ST890CDR
| Parameters | |
|---|---|
| Lead Free | Lead Free |
| Factory Lead Time | 10 Weeks |
| Lifecycle Status | ACTIVE (Last Updated: 7 months ago) |
| Mount | Surface Mount |
| Mounting Type | Surface Mount |
| Package / Case | 8-SOIC (0.154, 3.90mm Width) |
| Number of Pins | 8 |
| Operating Temperature | -40°C~85°C TA |
| Packaging | Tape & Reel (TR) |
| JESD-609 Code | e4 |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 8 |
| ECCN Code | EAR99 |
| Resistance | 90mOhm |
| Terminal Finish | Nickel/Palladium/Gold (Ni/Pd/Au) |
| Subcategory | Peripheral Drivers |
| Terminal Position | DUAL |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 260 |
| Number of Functions | 1 |
| Supply Voltage | 3V |
| Current Rating | 1.2A |
| Time@Peak Reflow Temperature-Max (s) | 30 |
| Base Part Number | ST890 |
| Pin Count | 8 |
| Number of Outputs | 1 |
| Output Type | P-Channel |
| Max Output Current | 1.2A |
| Operating Supply Voltage | 5.5V |
| Power Supplies | 3/5V |
| Interface | On/Off |
| Nominal Supply Current | 13mA |
| Output Configuration | High Side |
| Output Current | 1.2A |
| Voltage - Supply (Vcc/Vdd) | Not Required |
| Max Supply Current | 13mA |
| Input Type | Non-Inverting |
| Turn On Delay Time | 50 μs |
| Switch Type | General Purpose |
| Min Input Voltage | 2.7V |
| Max Input Voltage | 5.5V |
| Nominal Input Voltage | 5.5V |
| Turn-Off Delay Time | 10 μs |
| Ratio - Input:Output | 1:1 |
| Voltage - Load | 2.7V~5.5V |
| Driver Number of Bits | 1 |
| Fault Protection | Current Limiting (Adjustable), Over Temperature |
| Output Peak Current Limit-Nom | 1.2A |
| Rds On (Typ) | 75m Ω |
| Built-in Protections | OVER CURRENT; THERMAL |
| Length | 4.9mm |
| Width | 3.9mm |
| Radiation Hardening | No |
| RoHS Status | ROHS3 Compliant |
ST890CDR Overview
Tape & Reel (TR) is how it's packaged.This file is included in package 8-SOIC (0.154, 3.90mm Width).The lighting driver is mounted in the Surface Mount position.The switch type of this switch is General Purpose.To ensure reliable performance, the temperature should be set to -40°C~85°C TA.As a default, the output is set to 1.Operation is based on Not Required supply voltage.A maximum output voltage of P-Channel volts can be achieved by this LED driver.It belongs to the family ST890.A total of 8 terminations have been found in it.It is necessary to use the 8 pins in order to operate the LED driver.It consists of 1 functions.To comply with the operation criteria, the maximum output current is reduced to 1.2A.Using a voltage of 3V allows for high efficiency.Surface Mount is mounted in the way of this LED driving board.It is equipped with a total of 8 pins.It has 90mOhm resistance.This case results in a 1.2A output current.The LED driver is packaged in an econtainer with a capacity of Peripheral Drivers.The power supply of the part is 3/5V.In order to maximize efficiency, the supply voltage should be set at 5.5V.Input voltage is limited to 5.5V volts.A voltage of 2.7V volts is the minimum input voltage.This system has a maximum current requirement of 13mA.
ST890CDR Features
Supplied from 3V
Resistance of 90mOhm
ST890CDR Applications
There are a lot of STMicroelectronics ST890CDR Power Switches ICs applications.
- Wireless Headsets
- Hot-Swap Systems
- HDD, SSD
- Solid State Drivers
- Wearable Devices
- Low Voltage I/O System Power
- Storage (HDDs, SSDs)
- Various applications equipped with buttons
- Portable Video Game Players
- USB3.1 Power Delivery