SN74LVCH32374AGKER
| Parameters | |
|---|---|
| Mount | Surface Mount |
| Mounting Type | Surface Mount |
| Package / Case | 96-LFBGA |
| Number of Pins | 96 |
| Weight | 174.20782mg |
| Operating Temperature | -40°C~85°C TA |
| Packaging | Tape & Reel (TR) |
| Series | 74LVCH |
| JESD-609 Code | e0 |
| Pbfree Code | no |
| Part Status | Obsolete |
| Moisture Sensitivity Level (MSL) | 3 (168 Hours) |
| Number of Terminations | 96 |
| ECCN Code | EAR99 |
| Type | D-Type |
| Terminal Finish | Tin/Lead (Sn/Pb) |
| Additional Feature | BUS HOLD INPUTS ELIMINATE THE NEED FOR EXTERNAL PULLUP/PULLDOWN RESISTORS |
| Subcategory | FF/Latches |
| Packing Method | TAPE AND REEL |
| Technology | CMOS |
| Voltage - Supply | 1.65V~3.6V |
| Terminal Position | BOTTOM |
| Terminal Form | BALL |
| Peak Reflow Temperature (Cel) | 235 |
| Supply Voltage | 1.8V |
| Base Part Number | 74LVCH32374 |
| Function | Standard |
| Output Type | Tri-State, Non-Inverted |
| Number of Elements | 4 |
| Polarity | Non-Inverting |
| Supply Voltage-Min (Vsup) | 1.65V |
| Load Capacitance | 50pF |
| Number of Ports | 2 |
| Number of Bits | 32 |
| Clock Frequency | 150MHz |
| Propagation Delay | 4.9 ns |
| Turn On Delay Time | 1.5 ns |
| Family | LVC/LCX/Z |
| Logic Function | D-Type, Flip-Flop |
| Current - Quiescent (Iq) | 40μA |
| Current - Output High, Low | 24mA 24mA |
| Number of Bits per Element | 8 |
| Max Propagation Delay @ V, Max CL | 4.5ns @ 3.3V, 50pF |
| Trigger Type | Positive Edge |
| Input Capacitance | 5pF |
| Number of Output Lines | 3 |
| Clock Edge Trigger Type | Positive Edge |
| Max Frequency@Nom-Sup | 150000000Hz |
| Width | 5.5mm |
| Radiation Hardening | No |
| RoHS Status | ROHS3 Compliant |
| Lead Free | Contains Lead |
SN74LVCH32374AGKER Overview
96-LFBGAis the way it is packaged. It is included in the package Tape & Reel (TR). T flip flop is configured with an output of Tri-State, Non-Inverted. In the configuration of the trigger, Positive Edgeis used. In this case, the electronic component is mounted in the way of Surface Mount. Powered by a 1.65V~3.6Vvolt supply, it operates as follows. Currently, the operating temperature is -40°C~85°C TA. D-Typeis the type of this D latch. FPGAs belonging to the 74LVCHseries contain this type of chip. This D flip flop should not have a frequency greater than 150MHz. A total of 4elements are present in it. It consumes 40μA of quiescent current without being affected by external factors. Terminations are 96. D latch belongs to the 74LVCH32374 family. An input voltage of 1.8Vpowers the D latch. This JK flip flop has a 5pFfarad input capacitance. It is a member of the LVC/LCX/Zfamily of D flip flop. In this case, the electronic component is mounted in the way of Surface Mount. Basically, it is designed with a set of 96 pins. This device exhibits a clock edge trigger type of Positive Edge. The part you are looking for is included in FF/Latches. It is designed with a number of bits of 32. The supply voltage (Vsup) should be kept above 1.65V for normal operation. Due to its reliability, this T flip flop is well suited for TAPE AND REEL. The D flip flop is embedded with 2ports. There are 3 output lines on it. In addition, you can refer to the additinal BUS HOLD INPUTS ELIMINATE THE NEED FOR EXTERNAL PULLUP/PULLDOWN RESISTORS of the D latch.
SN74LVCH32374AGKER Features
Tape & Reel (TR) package
74LVCH series
96 pins
32 Bits
SN74LVCH32374AGKER Applications
There are a lot of Texas Instruments SN74LVCH32374AGKER Flip Flops applications.
- Counters
- Storage Registers
- Guaranteed simultaneous switching noise level
- Single Up Count-Control Line
- Individual Asynchronous Resets
- ATE
- Bounce elimination switch
- Computers
- Bus hold
- Convert a momentary switch to a toggle switch