SN74LVC574ANSRG4
| Parameters | |
|---|---|
| Mount | Surface Mount |
| Package / Case | SOP |
| Number of Pins | 20 |
| Weight | 266.712314mg |
| Packaging | Tape & Reel (TR) |
| JESD-609 Code | e4 |
| Moisture Sensitivity Level (MSL) | 1 |
| Number of Terminations | 20 |
| Terminal Finish | Nickel/Palladium/Gold (Ni/Pd/Au) |
| Max Operating Temperature | 125°C |
| Min Operating Temperature | -40°C |
| Subcategory | FF/Latches |
| Packing Method | TR |
| Technology | CMOS |
| Terminal Position | DUAL |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 260 |
| Number of Functions | 1 |
| Supply Voltage | 1.8V |
| Frequency | 150MHz |
| Pin Count | 20 |
| Number of Elements | 1 |
| Polarity | Non-Inverting |
| Power Supplies | 3.3V |
| Temperature Grade | AUTOMOTIVE |
| Max Supply Voltage | 3.6V |
| Min Supply Voltage | 1.65V |
| Load Capacitance | 50pF |
| Number of Ports | 2 |
| Current - Output | 24mA |
| Propagation Delay | 7.8 ns |
| Turn On Delay Time | 7 ns |
| Family | LVC/LCX/Z |
| Logic Function | D-Type, Flip-Flop |
| Output Characteristics | 3-STATE |
| Logic IC Type | BUS DRIVER |
| Max I(ol) | 0.024 A |
| Number of Bits per Element | 8 |
| High Level Output Current | -24mA |
| Low Level Output Current | 24mA |
| Control Type | INDEPENDENT CONTROL |
| Count Direction | UNIDIRECTIONAL |
| Clock Edge Trigger Type | Positive Edge |
| Translation | N/A |
| Height Seated (Max) | 2mm |
| Width | 5.3mm |
| Radiation Hardening | No |
| RoHS Status | RoHS Compliant |
| Lead Free | Lead Free |
SN74LVC574ANSRG4 Overview
It is embeded in SOP case. As part of the package Tape & Reel (TR), it is embedded. In total, it contains 1 elements. In 20terminations, a transmission line is terminated with a JK flip flop that matches its characteristic impedance. The power source is powered by 1.8V. The electronic device belongs to the LVC/LCX/Zfamily. This electronic part is mounted in the way of Surface Mount. This board has 20 pins. This device exhibits a clock edge trigger type of Positive Edge. It is part of the FF/Latchesbase part number family. Considering the reliability of this T flip flop, it is well suited for TR. It operates from 3.3V power supplies. A D flip flop with 2embedded ports is available. There is -24mA output current at the high level. 24mAis set as the low level output current. A temperature below 125°Cis recommended for operation. Operating temperatures should be above -40°C. In order for it to operate, a supply voltage of 1.65Vis required. 3.6Vis the maximum supply voltage supported by it. The frequency that can be achieved is 150MHz. It adopts a logic IC of type BUS DRIVER. It is equipped with 1 Functions . A total of 20 pins are present on this device. 24mA provides maximum design flexibility due to its output current.
SN74LVC574ANSRG4 Features
Tape & Reel (TR) package
20 pins
3.3V power supplies
1 Functions
20 pin count
SN74LVC574ANSRG4 Applications
There are a lot of Texas Instruments SN74LVC574ANSRG4 Flip Flops applications.
- Consumer
- Common Clocks
- Event Detectors
- Single Down Count-Control Line
- ESD performance
- Registers
- Frequency Dividers
- Guaranteed simultaneous switching noise level
- Functionally equivalent to the MC10/100EL29
- Dynamic threshold performance