SN74LVC32374AGKER
| Parameters | |
|---|---|
| Mount | Surface Mount |
| Mounting Type | Surface Mount |
| Package / Case | 96-LFBGA |
| Number of Pins | 96 |
| Weight | 174.20782mg |
| Operating Temperature | -40°C~85°C TA |
| Packaging | Cut Tape (CT) |
| Series | 74LVC |
| JESD-609 Code | e0 |
| Pbfree Code | no |
| Part Status | Obsolete |
| Moisture Sensitivity Level (MSL) | 3 (168 Hours) |
| Number of Terminations | 96 |
| ECCN Code | EAR99 |
| Type | D-Type |
| Terminal Finish | Tin/Lead (Sn/Pb) |
| Subcategory | Bus Driver/Transceiver |
| Packing Method | TAPE AND REEL |
| Technology | CMOS |
| Voltage - Supply | 1.65V~3.6V |
| Terminal Position | BOTTOM |
| Terminal Form | BALL |
| Peak Reflow Temperature (Cel) | 235 |
| Supply Voltage | 1.8V |
| Reach Compliance Code | not_compliant |
| Time@Peak Reflow Temperature-Max (s) | NOT SPECIFIED |
| Base Part Number | 74LVC32374 |
| Function | Standard |
| Qualification Status | Not Qualified |
| Output Type | Tri-State, Non-Inverted |
| Number of Elements | 4 |
| Polarity | Non-Inverting |
| Supply Voltage-Max (Vsup) | 3.6V |
| Power Supplies | 3.3V |
| Supply Voltage-Min (Vsup) | 1.65V |
| Load Capacitance | 50pF |
| Number of Ports | 2 |
| Number of Bits | 32 |
| Clock Frequency | 150MHz |
| Propagation Delay | 4.9 ns |
| Turn On Delay Time | 1.5 ns |
| Family | LVC/LCX/Z |
| Logic Function | D-Type, Flip-Flop |
| Current - Quiescent (Iq) | 40μA |
| Output Characteristics | 3-STATE |
| Current - Output High, Low | 24mA 24mA |
| Max Propagation Delay @ V, Max CL | 4.5ns @ 3.3V, 50pF |
| Trigger Type | Positive Edge |
| Input Capacitance | 5pF |
| Number of Output Lines | 8 |
| Clock Edge Trigger Type | Positive Edge |
| Max Frequency@Nom-Sup | 150000000Hz |
| Length | 13.5mm |
| Width | 5.5mm |
| RoHS Status | ROHS3 Compliant |
| Lead Free | Contains Lead |
SN74LVC32374AGKER Overview
It is embeded in 96-LFBGA case. It is contained within the Cut Tape (CT)package. T flip flop uses Tri-State, Non-Invertedas the output. In the configuration of the trigger, Positive Edgeis used. Surface Mountis occupied by this electronic component. Powered by a 1.65V~3.6Vvolt supply, it operates as follows. A temperature of -40°C~85°C TAis considered to be the operating temperature. It belongs to the type D-Typeof flip flops. In FPGA terms, D flip flop is a type of 74LVCseries FPGA. You should not exceed 150MHzin its output frequency. A total of 4elements are present in it. As a result, it consumes 40μA of quiescent current without being affected by external factors. In 96terminations, a transmission line is terminated with a JK flip flop that matches its characteristic impedance. Members of the 74LVC32374family make up this object. Power is provided by a 1.8V supply. This JK flip flop has a 5pFfarad input capacitance. In terms of electronic devices, this device belongs to the LVC/LCX/Zfamily of devices. It is mounted in the way of Surface Mount. This board has 96 pins. This device's clock edge trigger type is Positive Edge. The part you are looking for is included in Bus Driver/Transceiver. 32bits are used in its design. In this case, the maximum supply voltage (Vsup) reaches 3.6V. If you want to maintain normal operation, you should keep the supply voltage (Vsup) above 1.65V. On the basis of its reliable performance, this D flip flop is well suited for use with TAPE AND REEL. The D latch runs on a voltage of 3.3V volts. The D flip flop has no ports embedded. It operates with 8 output lines.
SN74LVC32374AGKER Features
Cut Tape (CT) package
74LVC series
96 pins
32 Bits
3.3V power supplies
SN74LVC32374AGKER Applications
There are a lot of Texas Instruments SN74LVC32374AGKER Flip Flops applications.
- Computers
- Memory
- Reduced system switching noise
- Shift Registers
- Storage registers
- Circuit Design
- Synchronous counter
- Pattern generators
- Latch-up performance
- Control circuits