SN74LVC2G66DCUT
| Parameters | |
|---|---|
| Factory Lead Time | 6 Weeks |
| Lifecycle Status | ACTIVE (Last Updated: 4 days ago) |
| Mount | Surface Mount |
| Mounting Type | Surface Mount |
| Package / Case | 8-VFSOP (0.091, 2.30mm Width) |
| Number of Pins | 8 |
| Weight | 9.610488mg |
| Operating Temperature | -40°C~85°C TA |
| Packaging | Tape & Reel (TR) |
| JESD-609 Code | e4 |
| Pbfree Code | yes |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 8 |
| Termination | SMD/SMT |
| Resistance | 10Ohm |
| Terminal Finish | Nickel/Palladium/Gold (Ni/Pd/Au) |
| Subcategory | Multiplexers or Switches |
| Technology | CMOS |
| Terminal Position | DUAL |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 260 |
| Number of Functions | 2 |
| Supply Voltage | 2.3V |
| Terminal Pitch | 0.5mm |
| Base Part Number | 74LVC2G66 |
| Output | SEPARATE OUTPUT |
| Pin Count | 8 |
| Power Supplies | 3.3V |
| Number of Channels | 2 |
| Max Supply Voltage | 5.5V |
| Min Supply Voltage | 1.65V |
| Operating Supply Current | 10μA |
| Max Supply Current | 1μA |
| Throw Configuration | SPST |
| Propagation Delay | 600 ps |
| Turn On Delay Time | 10 ns |
| Supply Type | Single |
| Bandwidth | 300MHz |
| Turn-Off Delay Time | 10.5 ns |
| -3db Bandwidth | 300MHz |
| On-State Resistance (Max) | 10Ohm |
| Multiplexer/Demultiplexer Circuit | 1:1 |
| Off-state Isolation-Nom | 42 dB |
| Current - Leakage (IS(off)) (Max) | 100nA |
| Channel Capacitance (CS(off), CD(off)) | 6pF |
| On-state Resistance Match-Nom | 5Ohm |
| Switch Circuit | SPST - NO |
| Switch Time (Ton, Toff) (Max) | 3.9ns, 6.3ns |
| Channel-to-Channel Matching (ΔRon) | 2 Ω (Max) |
| Crosstalk | -58dB @ 1MHz |
| Switching | MAKE-BEFORE-BREAK |
| Switch-on Time-Max | 5.6ns |
| Switch-off Time-Max | 6.9ns |
| Voltage - Supply, Single (V+) | 1.65V~5.5V |
| Normal Position | NO |
| Height | 900μm |
| Length | 2.3mm |
| Width | 2mm |
| Thickness | 850μm |
| Radiation Hardening | No |
| REACH SVHC | No SVHC |
| RoHS Status | ROHS3 Compliant |
| Lead Free | Lead Free |
SN74LVC2G66DCUT Overview
Due to its 8-VFSOP (0.091, 2.30mm Width) packaging, the electronic part is convenient for international shipping. A high level of reliability can be achieved through the use of an advanced packaging method Tape & Reel (TR). Mounted in Surface Mount is this multiplexer. 1:1 is the ratio of multiplexer to demultiplexer circuits. Operation at a temperature around -40°C~85°C TA. 8 terminations have been made so far. High-quality output is provided by the electronic component's 2 channels. A 2.3V voltage supply should turn on and run the electronic component. A total of 8 pins are injected into the body of the electronic part. Unlike digital switches, these are based on SPST - NO switching circuits. Search with 74LVC2G66 if you are looking for analog multiplexer variants. An switch multiplexer with 10Ohm internal resistance has a value of 10Ohm. The datasheets for the 8 pins explain the functions. In this analog multiplexer, the value is Multiplexers or Switches. Multiplexers should not be powered above 5.5V in normal situations. Single supply type digital switch with a low cost. In order for the electronic part to function properly, the lowest voltage should be 1.65V. An operating current of 10μA would be sufficient for this switch device. Using a single voltage supply, this switch device consumes 1.65V~5.5V volts. When the digital multiplexer is charged above 1μA, damage can occur. A total of SEPARATE OUTPUT outputs are available on this analog switch ic. The data can be transferred over a wide range of bandwidths, called 300MHz bandwidths.
SN74LVC2G66DCUT Features
2 Channels
Switch Circuit: SPST - NO
10μA Supply Current
-3db Bandwidth: 300MHz
Bandwidth: 300MHz
SN74LVC2G66DCUT Applications
There are a lot of Texas Instruments SN74LVC2G66DCUT Analog Switches & Multiplexers ICs applications.
- Communication systems
- Audio and video signal routing
- Video signal routing
- Remote wireless modules
- DSLAMs
- Medical
- High-Voltage
- E1 Network Equipment
- New designs requiring multiplexer functions
- SONET