SN74LVC1G66DBVT
| Parameters | |
|---|---|
| Factory Lead Time | 6 Weeks |
| Lifecycle Status | ACTIVE (Last Updated: 2 days ago) |
| Mount | Surface Mount |
| Mounting Type | Surface Mount |
| Package / Case | SC-74A, SOT-753 |
| Number of Pins | 5 |
| Weight | 11.198062mg |
| Operating Temperature | -40°C~85°C TA |
| Packaging | Tape & Reel (TR) |
| JESD-609 Code | e4 |
| Pbfree Code | yes |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 5 |
| Resistance | 10Ohm |
| Terminal Finish | Nickel/Palladium/Gold (Ni/Pd/Au) |
| Terminal Position | DUAL |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 260 |
| Number of Functions | 1 |
| Supply Voltage | 1.8V |
| Base Part Number | 74LVC1G66 |
| Pin Count | 5 |
| Number of Channels | 1 |
| Max Supply Voltage | 5.5V |
| Min Supply Voltage | 1.65V |
| Analog IC - Other Type | SPDT |
| Operating Supply Current | 10μA |
| Nominal Supply Current | 1μA |
| Max Supply Current | 10μA |
| Throw Configuration | SPST |
| Propagation Delay | 600 ps |
| Turn On Delay Time | 4.2 ns |
| Supply Type | Single |
| Bandwidth | 195MHz |
| Turn-Off Delay Time | 5 ns |
| -3db Bandwidth | 300MHz |
| On-State Resistance (Max) | 10Ohm |
| Multiplexer/Demultiplexer Circuit | 1:1 |
| Off-state Isolation-Nom | 58 dB |
| Current - Leakage (IS(off)) (Max) | 100nA |
| Channel Capacitance (CS(off), CD(off)) | 6pF |
| On-state Resistance Match-Nom | 12Ohm |
| Switch Circuit | SPST - NO |
| Switch Time (Ton, Toff) (Max) | 4.2ns, 5ns |
| Switching | BREAK-BEFORE-MAKE |
| Voltage - Supply, Single (V+) | 1.65V~5.5V |
| Drain to Source Resistance | 12Ohm |
| Normal Position | NC |
| Height | 1.45mm |
| Length | 2.9mm |
| Width | 1.6mm |
| Thickness | 1.2mm |
| Radiation Hardening | No |
| REACH SVHC | No SVHC |
| RoHS Status | ROHS3 Compliant |
| Lead Free | Lead Free |
SN74LVC1G66DBVT Overview
The electrical component comes in SC-74A, SOT-753 packaging, which makes it convenient to ship overseas. High reliability is achieved by using advanced packaging method Tape & Reel (TR). A switch device like this is mounted in Surface Mount. 1:1 is the number of circuits in the multiplexer and demultiplexer. Increasing operating temperature to around -40°C~85°C TA. A total of 5 terminations have been recorded. By its 1 channels, the electronic component provides high-quality output. When the electronic component is given a voltage of 1.8V, it should be turned on and run. There are 5 pins injected into the electronic part body. Multiplexers built on a SPST - NO switching circuit are built. Using the 74LVC1G66 search parameter, you can discover variants of the switch. This digital multiplexer has 10Ohm internal resistance. To find out what the functions of 5 pins are, please refer to their datasheets. normally, users should not supply switches with voltages higher than 5.5V. Single supply type digital switch with a low cost. It is recommended that the electrical component receives a voltage of 1.65V. The analogue multiplexer could operate on 10μA current. Analogue multiplexers require a 1.65V~5.5V voltage to drain from a single voltage supply. Putting voltage greater than 10μA on the multiplexer may cause damage. A SPDT analog IC is integrated into the board. It is possible to transfer data over a 195MHz-bandwidth. It has a Drain to Source resistance of 12Ohm ohms.
SN74LVC1G66DBVT Features
1 Channels
Switch Circuit: SPST - NO
10μA Supply Current
-3db Bandwidth: 300MHz
Bandwidth: 195MHz
Drain-to-Source resistance: 12Ohm
SN74LVC1G66DBVT Applications
There are a lot of Texas Instruments SN74LVC1G66DBVT Analog Switches & Multiplexers ICs applications.
- High-Voltage
- Routers
- Avionics
- Sample-and-hold systems
- Audio signal routing
- Modems
- Industrial
- Precision test equipment
- Isolation
- CSU