SN74LV174APWRG4
| Parameters | |
|---|---|
| Lifecycle Status | ACTIVE (Last Updated: 6 days ago) |
| Mount | Surface Mount |
| Package / Case | TSSOP |
| Number of Pins | 16 |
| Weight | 61.887009mg |
| Packaging | Tape & Reel (TR) |
| JESD-609 Code | e4 |
| Pbfree Code | yes |
| Moisture Sensitivity Level (MSL) | 1 |
| Number of Terminations | 16 |
| ECCN Code | EAR99 |
| Terminal Finish | Nickel/Palladium/Gold (Ni/Pd/Au) |
| Max Operating Temperature | 85°C |
| Min Operating Temperature | -40°C |
| Subcategory | FF/Latches |
| Packing Method | TR |
| Technology | CMOS |
| Terminal Position | DUAL |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 260 |
| Number of Functions | 1 |
| Supply Voltage | 2.5V |
| Frequency | 180MHz |
| Pin Count | 16 |
| Polarity | Non-Inverting |
| Power Supplies | 3.3V |
| Temperature Grade | INDUSTRIAL |
| Number of Circuits | 7 |
| Max Supply Voltage | 5.5V |
| Min Supply Voltage | 2V |
| Load Capacitance | 50pF |
| Current - Output | 12mA |
| Number of Bits | 6 |
| Propagation Delay | 20.6 ns |
| Turn On Delay Time | 3 ns |
| Family | LV/LV-A/LVX/H |
| Logic Function | D-Type, Flip-Flop |
| Logic IC Type | D FLIP-FLOP |
| High Level Output Current | -12mA |
| Low Level Output Current | 12mA |
| Number of Input Lines | 2 |
| Number of Output Lines | 1 |
| Clock Edge Trigger Type | Positive Edge |
| Height | 1.2mm |
| Length | 5mm |
| Width | 4.4mm |
| Thickness | 1mm |
| Radiation Hardening | No |
| RoHS Status | RoHS Compliant |
| Lead Free | Lead Free |
SN74LV174APWRG4 Overview
In the form of TSSOP, it has been packaged. D flip flop is included in the Tape & Reel (TR)package. 16terminations have occurred. A voltage of 2.5V provides power to the D latch. An electronic device belonging to the family LV/LV-A/LVX/Hcan be found here. In this case, the electronic component is mounted in the way of Surface Mount. A total of 16pins are provided on this board. This device exhibits a clock edge trigger type of Positive Edge. The part you are looking for is included in FF/Latches. It is designed with a number of bits of 6. In order to achieve its superior flexibility, 7 circuits are used. In light of its reliable performance, this T flip flop is well suited for TR. A power supply of 3.3Vis required to operate it. There are 1 output lines on it. Currently, there are 2 input lines present. -12mA is set as the high level output current. There is no low level output current set at 12mA. Ideally, the operating temperature should be lower than 85°C. Ideally, the operating temperature should be higher than -40°C. The RS flip flop is designed to operate with a minimal supply voltage of 2VV. There is a maximum voltage support of 5.5V. It is possible to achieve 180MHz frequencies. This logic IC is D FLIP-FLOP. The T flip flop is equipped with 1functions . It is equipped with 16 pins. With an output current of 12mA, this flip flop offers maximum design flexibility.
SN74LV174APWRG4 Features
Tape & Reel (TR) package
16 pins
6 Bits
3.3V power supplies
1 Functions
16 pin count
SN74LV174APWRG4 Applications
There are a lot of Texas Instruments SN74LV174APWRG4 Flip Flops applications.
- Power down protection
- Balanced Propagation Delays
- Test & Measurement
- Frequency Divider circuits
- Counters
- Memory
- Instrumentation
- Individual Asynchronous Resets
- Convert a momentary switch to a toggle switch
- Reduced system switching noise