SN74LS107AD
| Parameters | |
|---|---|
| Factory Lead Time | 6 Weeks |
| Lifecycle Status | ACTIVE (Last Updated: 3 days ago) |
| Mount | Surface Mount |
| Mounting Type | Surface Mount |
| Package / Case | 14-SOIC (0.154, 3.90mm Width) |
| Number of Pins | 14 |
| Weight | 129.387224mg |
| Operating Temperature | 0°C~70°C TA |
| Packaging | Tube |
| Series | 74LS |
| JESD-609 Code | e4 |
| Pbfree Code | yes |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 14 |
| ECCN Code | EAR99 |
| Type | JK Type |
| Terminal Finish | Nickel/Palladium/Gold (Ni/Pd/Au) |
| Subcategory | FF/Latches |
| Technology | TTL |
| Voltage - Supply | 4.75V~5.25V |
| Terminal Position | DUAL |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 260 |
| Supply Voltage | 5V |
| Base Part Number | 74LS107 |
| Function | Reset |
| Output Type | Differential |
| Operating Supply Voltage | 5V |
| Polarity | Non-Inverting |
| Power Supplies | 5V |
| Number of Channels | 2 |
| Output Current | 8mA |
| Clock Frequency | 45MHz |
| Propagation Delay | 20 ns |
| Turn On Delay Time | 15 ns |
| Family | LS |
| Logic Function | Flip-Flop, JK-Type |
| Current - Quiescent (Iq) | 6mA |
| Current - Output High, Low | 400μA 8mA |
| Max I(ol) | 0.008 A |
| Number of Bits per Element | 1 |
| Max Propagation Delay @ V, Max CL | 20ns @ 5V, 15pF |
| Trigger Type | Negative Edge |
| Schmitt Trigger | No |
| Power Supply Current-Max (ICC) | 6mA |
| Number of Input Lines | 4 |
| fmax-Min | 30 MHz |
| Clock Edge Trigger Type | Negative Edge |
| Max Frequency@Nom-Sup | 30000000Hz |
| Height | 1.75mm |
| Length | 8.65mm |
| Width | 3.91mm |
| Thickness | 1.58mm |
| Radiation Hardening | No |
| REACH SVHC | No SVHC |
| RoHS Status | ROHS3 Compliant |
| Lead Free | Lead Free |
SN74LS107AD Overview
It is embeded in 14-SOIC (0.154, 3.90mm Width) case. D flip flop is included in the Tubepackage. There is a Differentialoutput configured with it. It is configured with a trigger that uses a value of Negative Edge. There is an electronic component mounted in the way of Surface Mount. A supply voltage of 4.75V~5.25V is required for operation. A temperature of 0°C~70°C TAis used in the operation. JK Typeis the type of this D latch. The FPGA belongs to the 74LS series. In order for it to function properly, its output frequency should not exceed 45MHz. There is a consumption of 6mAof quiescent energy. Terminations are 14. This D latch belongs to the family of 74LS107. A voltage of 5V provides power to the D latch. It is a member of the LSfamily of D flip flop. Surface Mount mounts this electronic component. This board has 14 pins. This device exhibits a clock edge trigger type of Negative Edge. It is included in FF/Latches. The system runs on a power supply of 5V watts. In order to achieve high efficiency, the supply voltage should be maintained at 5V. As a result of its output current of 8mA, it is very flexible in terms of design. Currently, there are 4 input lines present. Currently, there are 2 channels available.
SN74LS107AD Features
Tube package
74LS series
14 pins
5V power supplies
SN74LS107AD Applications
There are a lot of Texas Instruments SN74LS107AD Flip Flops applications.
- Parallel data storage
- Balanced Propagation Delays
- Communications
- Frequency Divider circuits
- CMOS Process
- Set-reset capability
- Memory
- Digital electronics systems
- 2 – Bit synchronous counter
- Data storage