SN74HCT273PWR
| Parameters | |
|---|---|
| Factory Lead Time | 6 Weeks |
| Lifecycle Status | ACTIVE (Last Updated: 4 days ago) |
| Mount | Surface Mount |
| Mounting Type | Surface Mount |
| Package / Case | 20-TSSOP (0.173, 4.40mm Width) |
| Number of Pins | 20 |
| Weight | 76.997305mg |
| Operating Temperature | -40°C~85°C TA |
| Packaging | Cut Tape (CT) |
| Series | 74HCT |
| JESD-609 Code | e4 |
| Pbfree Code | yes |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 20 |
| ECCN Code | EAR99 |
| Type | D-Type |
| Terminal Finish | Nickel/Palladium/Gold (Ni/Pd/Au) |
| Subcategory | FF/Latches |
| Packing Method | TR |
| Technology | CMOS |
| Voltage - Supply | 4.5V~5.5V |
| Terminal Position | DUAL |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 260 |
| Supply Voltage | 5V |
| Terminal Pitch | 0.65mm |
| Base Part Number | 74HCT273 |
| Function | Master Reset |
| Output Type | Non-Inverted |
| Operating Supply Voltage | 5V |
| Number of Elements | 1 |
| Polarity | Non-Inverting |
| Power Supplies | 5V |
| Number of Circuits | 8 |
| Load Capacitance | 50pF |
| Output Current | 50mA |
| Number of Bits | 8 |
| Clock Frequency | 37MHz |
| Propagation Delay | 42 ns |
| Turn On Delay Time | 15 ns |
| Family | HCT |
| Logic Function | D-Type, Flip-Flop |
| Current - Quiescent (Iq) | 8μA |
| Current - Output High, Low | 4mA 4mA |
| Max I(ol) | 0.004 A |
| Max Propagation Delay @ V, Max CL | 29ns @ 5.5V, 50pF |
| Trigger Type | Positive Edge |
| Input Capacitance | 3pF |
| Number of Input Lines | 3 |
| Clock Edge Trigger Type | Positive Edge |
| Height | 1.2mm |
| Length | 6.5mm |
| Width | 4.4mm |
| Thickness | 1mm |
| Radiation Hardening | No |
| REACH SVHC | No SVHC |
| RoHS Status | ROHS3 Compliant |
| Lead Free | Lead Free |
SN74HCT273PWR Overview
The package is in the form of 20-TSSOP (0.173, 4.40mm Width). D flip flop is embedded in the Cut Tape (CT) package. It is configured with Non-Invertedas an output. It is configured with a trigger that uses Positive Edge. There is an electronic component mounted in the way of Surface Mount. A voltage of 4.5V~5.5Vis used as the supply voltage. In the operating environment, the temperature is -40°C~85°C TA. This logic flip flop is classified as type D-Type. The FPGA belongs to the 74HCT series. This D flip flop should not have a frequency greater than 37MHz. D latch consists of 1 elements. It consumes 8μA of quiescent current without being affected by external factors. 20terminations have occurred. D latch belongs to the 74HCT273 family. Power is provided by a 5V supply. There is 3pF input capacitance for this T flip flop. In terms of electronic devices, this device belongs to the HCTfamily of devices. This electronic part is mounted in the way of Surface Mount. As you can see from the design, it has pins with 20. A Positive Edgeclock edge trigger is used in this device. There is a FF/Latchesbase part number assigned to the RS flip flops. An electronic part with 8bits has been designed. The superior flexibility is achieved through the use of 8 circuits. Considering the reliability of this T flip flop, it is well suited for TR. A total of 5V power supplies are needed to run it. Optimal efficiency requires a supply voltage of 5V. Its output current of 50mAallows for maximum design flexibility. This input has 3lines in it.
SN74HCT273PWR Features
Cut Tape (CT) package
74HCT series
20 pins
8 Bits
5V power supplies
SN74HCT273PWR Applications
There are a lot of Texas Instruments SN74HCT273PWR Flip Flops applications.
- Pattern generators
- Patented noise
- Guaranteed simultaneous switching noise level
- ATE
- ESD performance
- ESCC
- Reduced system switching noise
- Test & Measurement
- Count Modes
- Differential Individual