SN74HC273NSRG4
| Parameters | |
|---|---|
| Number of Input Lines | 2 |
| Number of Output Lines | 1 |
| Clock Edge Trigger Type | Positive Edge |
| Width | 5.3mm |
| Radiation Hardening | No |
| RoHS Status | RoHS Compliant |
| Lead Free | Lead Free |
| Mount | Surface Mount |
| Package / Case | SOP |
| Number of Pins | 20 |
| Weight | 266.712314mg |
| Packaging | Tape & Reel (TR) |
| JESD-609 Code | e4 |
| Moisture Sensitivity Level (MSL) | 1 |
| Number of Terminations | 20 |
| ECCN Code | EAR99 |
| Terminal Finish | Nickel/Palladium/Gold (Ni/Pd/Au) |
| Max Operating Temperature | 85°C |
| Min Operating Temperature | -40°C |
| Additional Feature | DUMMY VAL |
| Subcategory | FF/Latches |
| Packing Method | TAPE AND REEL |
| Technology | CMOS |
| Terminal Position | DUAL |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 260 |
| Number of Functions | 1 |
| Supply Voltage | 5V |
| Frequency | 60MHz |
| Pin Count | 20 |
| Operating Supply Voltage | 5V |
| Polarity | Non-Inverting |
| Temperature Grade | INDUSTRIAL |
| Number of Circuits | 8 |
| Max Supply Voltage | 6V |
| Min Supply Voltage | 2V |
| Load Capacitance | 50pF |
| Current - Output | 5.2mA |
| Number of Bits | 8 |
| Propagation Delay | 160 ns |
| Turn On Delay Time | 13 ns |
| Family | HC/UH |
| Logic Function | D-Type, Flip-Flop |
| Logic IC Type | D FLIP-FLOP |
| Max I(ol) | 0.004 A |
| High Level Output Current | -5.2mA |
| Low Level Output Current | 5.2mA |
SN74HC273NSRG4 Overview
In the form of SOP, it has been packaged. It is contained within the Tape & Reel (TR)package. A total of 20 terminations have been made. The power supply voltage is 5V. In this case, the D flip flop belongs to the HC/UHfamily. It is mounted in the way of Surface Mount. It is designed with 20 pins. This device has Positive Edgeas its clock edge trigger type. There is a FF/Latchesbase part number assigned to the RS flip flops. 8bits are used in its design. The superior flexibility is achieved through the use of 8 circuits. Due to its reliability, this T flip flop is well suited for TAPE AND REEL. If high efficiency is desired, the supply voltage should be kept at 5V. There are 1 output lines in this JK flip flop. The number of input lines is 2. In addition, DUMMY VALis a characteristic of it. -5.2mA is set as the high level output current. There is no low level output current set at 5.2mA. If the operating temperature is lower than 85°C, it is recommended. It should be higher than -40°Cwhen the system is operating. The system operates with a minimum supply voltage of 2V. In this case, it supports a maximum supply voltage of 6V. 60MHzis the maximum frequency that can be achieved. This logic IC is D FLIP-FLOP. It is equipped with 1 Functions . 20pins are provided on the D latch. It features maximum design flexibility due to the 5.2mA output current.
SN74HC273NSRG4 Features
Tape & Reel (TR) package
20 pins
8 Bits
1 Functions
20 pin count
SN74HC273NSRG4 Applications
There are a lot of Texas Instruments SN74HC273NSRG4 Flip Flops applications.
- Bus hold
- Common Clocks
- Single Down Count-Control Line
- Frequency division
- CMOS Process
- ESD protection
- Latch
- Data storage
- Storage Registers
- High Performance Logic for test systems