SN74HC273DWG4
| Parameters | |
|---|---|
| Mount | Surface Mount |
| Package / Case | SOIC |
| Number of Pins | 20 |
| Weight | 500.709277mg |
| JESD-609 Code | e4 |
| Moisture Sensitivity Level (MSL) | 1 |
| Number of Terminations | 20 |
| ECCN Code | EAR99 |
| Terminal Finish | Nickel/Palladium/Gold (Ni/Pd/Au) |
| Max Operating Temperature | 85°C |
| Min Operating Temperature | -40°C |
| Additional Feature | DUMMY VAL |
| Subcategory | FF/Latches |
| Packing Method | TUBE |
| Technology | CMOS |
| Terminal Position | DUAL |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 260 |
| Number of Functions | 1 |
| Supply Voltage | 5V |
| Frequency | 60MHz |
| Time@Peak Reflow Temperature-Max (s) | NOT SPECIFIED |
| Pin Count | 20 |
| Qualification Status | Not Qualified |
| Operating Supply Voltage | 5V |
| Polarity | Non-Inverting |
| Temperature Grade | INDUSTRIAL |
| Number of Circuits | 8 |
| Max Supply Voltage | 6V |
| Min Supply Voltage | 2V |
| Load Capacitance | 50pF |
| Current - Output | 5.2mA |
| Number of Bits | 8 |
| Propagation Delay | 160 ns |
| Turn On Delay Time | 13 ns |
| Family | HC/UH |
| Logic Function | D-Type, Flip-Flop |
| Logic IC Type | D FLIP-FLOP |
| Max I(ol) | 0.004 A |
| High Level Output Current | -5.2mA |
| Low Level Output Current | 5.2mA |
| Number of Input Lines | 2 |
| Number of Output Lines | 1 |
| Clock Edge Trigger Type | Positive Edge |
| Height | 2.35mm |
| Length | 12.8mm |
| Width | 7.52mm |
| RoHS Status | RoHS Compliant |
| Lead Free | Lead Free |
SN74HC273DWG4 Overview
As a result, it is packaged as SOIC. The number of terminations is 20. Power is provided by a 5V supply. It belongs to the family of electronic devices known as HC/UH. Electronic part Surface Mountis mounted in the way. This board has 20 pins. This device's clock edge trigger type is Positive Edge. There is a base part number FF/Latchesfor the RS flip flops. 8bits are used in its design. To achieve this superior flexibility, 8 circuits are used. This D flip flop is well suited for TUBE based on its reliable performance. The supply voltage should be maintained at 5V for high efficiency. It is designed with 1 output lines. This input has 2lines in it. In addition, you can refer to the additinal DUMMY VAL of the D latch. -5.2mA is set as the high level output current. The low level output current is set to 5.2mA. There should be a temperature below 85°Cduring operation. If the operating temperature is higher than -40°C, the system should operate properly. It is powered by 2V as its minimum supply voltage. It supports a maximum supply voltage of 6V volts. The frequency that can be achieved is 60MHz. The logic IC it adopts is D FLIP-FLOP. Currently, it is equipped with 1 functions . 20pins are available on this JK flip flop. In addition to its maximum design flexibility, the output current of the flip flop is 5.2mA.
SN74HC273DWG4 Features
20 pins
8 Bits
1 Functions
20 pin count
SN74HC273DWG4 Applications
There are a lot of Texas Instruments SN74HC273DWG4 Flip Flops applications.
- QML qualified product
- Control circuits
- EMI reduction circuitry
- Buffered Clock
- Asynchronous counter
- Shift registers
- Frequency Divider circuits
- Power down protection
- CMOS Process
- Automotive