SN74AUC2G66DCUR
| Parameters | |
|---|---|
| Current - Leakage (IS(off)) (Max) | 1μA |
| Channel Capacitance (CS(off), CD(off)) | 2.5pF |
| On-state Resistance Match-Nom | 3Ohm |
| Switch Circuit | SPST - NO |
| Switch Time (Ton, Toff) (Max) | 2.3ns, 2ns |
| Channel-to-Channel Matching (ΔRon) | 1 Ω (Max) |
| Crosstalk | -60dB @ 1MHz |
| Switching | MAKE-BEFORE-BREAK |
| Switch-on Time-Max | 3ns |
| Voltage - Supply, Single (V+) | 0.8V~2.7V |
| Normal Position | NO |
| Height | 900μm |
| Length | 2.3mm |
| Width | 2mm |
| Thickness | 850μm |
| Radiation Hardening | No |
| RoHS Status | ROHS3 Compliant |
| Lead Free | Lead Free |
| Factory Lead Time | 6 Weeks |
| Lifecycle Status | ACTIVE (Last Updated: 4 days ago) |
| Contact Plating | Gold |
| Mount | Surface Mount |
| Mounting Type | Surface Mount |
| Package / Case | 8-VFSOP (0.091, 2.30mm Width) |
| Number of Pins | 8 |
| Weight | 10.007382mg |
| Operating Temperature | -40°C~85°C TA |
| Packaging | Tape & Reel (TR) |
| JESD-609 Code | e4 |
| Pbfree Code | yes |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 8 |
| ECCN Code | EAR99 |
| Resistance | 15Ohm |
| Subcategory | Multiplexer or Switches |
| Technology | CMOS |
| Terminal Position | DUAL |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 260 |
| Number of Functions | 2 |
| Supply Voltage | 1.1V |
| Terminal Pitch | 0.5mm |
| Base Part Number | 74AUC2G66 |
| Pin Count | 8 |
| Polarity | Non-Inverting |
| Number of Channels | 2 |
| Max Supply Voltage | 2.7V |
| Min Supply Voltage | 800mV |
| Operating Supply Current | 10μA |
| Max Supply Current | 10μA |
| Throw Configuration | SPST |
| Propagation Delay | 400 ps |
| Turn On Delay Time | 2.7 ns |
| Supply Type | Single |
| Bandwidth | 500MHz |
| Turn-Off Delay Time | 3.4 ns |
| -3db Bandwidth | 50MHz |
| On-State Resistance (Max) | 15Ohm |
| High Level Output Current | 50mA |
| Low Level Output Current | 50mA |
| Multiplexer/Demultiplexer Circuit | 1:1 |
| Off-state Isolation-Nom | 50 dB |
SN74AUC2G66DCUR Overview
Shipping overseas is convenient with the electronic component packed in 8-VFSOP (0.091, 2.30mm Width). High reliability is ensured by the advanced packaging method Tape & Reel (TR). This analog switch is mounted in Surface Mount. In the multiplexer and demultiplexer, 1:1 represents the number of circuits. Operation at a temperature around -40°C~85°C TA. Total terminations are 8. The electronic part delivers high-quality output through its 2 channels. If the voltage supply is 1.1V volts, the electrical component should be turned on and run. It is injected into the electrical part body with 8 pins. These analog multiplexers are built based on SPST - NO switching circuits. Try searching for 74AUC2G66 variants of the analog switch ic. It has an internal resistance of 15Ohm. You can find the functions of the 8 pins in the datasheets. This switch device is a typical Multiplexer or Switches. A voltage higher than 2.7V should not normally be supplied to the switches. Analogue multiplexers of the Single supply type that are cost-effective. In order for the electronic part to function properly, the lowest voltage should be 800mV. An operating current of 10μA would be sufficient for this switch device. Using only a single voltage supply, this analog switch requires 0.8V~2.7V voltage. A voltage higher than 10μA may cause damage to the switch multiplexer. This switch operates within the bandwidth of 500MHz.
SN74AUC2G66DCUR Features
2 Channels
Switch Circuit: SPST - NO
10μA Supply Current
-3db Bandwidth: 50MHz
Bandwidth: 500MHz
SN74AUC2G66DCUR Applications
There are a lot of Texas Instruments SN74AUC2G66DCUR Analog Switches & Multiplexers ICs applications.
- Channelized and Unchannelized DS3 applications
- Intelligent PBX
- Battery Powered Instruments
- Data Acquisition Systems
- SDH
- Modems
- Automatic test equipment
- Industrial control systems
- DSLAMs
- Multiplexers