SN74AUC1G66DBVR
| Parameters | |
|---|---|
| Factory Lead Time | 6 Weeks |
| Lifecycle Status | ACTIVE (Last Updated: 1 week ago) |
| Mount | Surface Mount |
| Mounting Type | Surface Mount |
| Package / Case | SC-74A, SOT-753 |
| Number of Pins | 5 |
| Weight | 11.198062mg |
| Operating Temperature | -40°C~85°C TA |
| Packaging | Cut Tape (CT) |
| JESD-609 Code | e4 |
| Pbfree Code | yes |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 5 |
| ECCN Code | EAR99 |
| Resistance | 15Ohm |
| Terminal Finish | Nickel/Palladium/Gold (Ni/Pd/Au) |
| Technology | CMOS |
| Terminal Position | DUAL |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 260 |
| Number of Functions | 1 |
| Supply Voltage | 1.65V |
| Time@Peak Reflow Temperature-Max (s) | NOT SPECIFIED |
| Base Part Number | 74AUC1G66 |
| Pin Count | 5 |
| Qualification Status | Not Qualified |
| Polarity | Non-Inverting |
| Number of Channels | 1 |
| Max Supply Voltage | 2.7V |
| Min Supply Voltage | 800mV |
| Operating Supply Current | 10μA |
| Max Supply Current | 10μA |
| Throw Configuration | SPST |
| Propagation Delay | 100 ps |
| Turn On Delay Time | 2.2 ns |
| Supply Type | Single |
| Bandwidth | 170MHz |
| Turn-Off Delay Time | 1.4 ns |
| -3db Bandwidth | 50MHz |
| On-State Resistance (Max) | 15Ohm |
| Multiplexer/Demultiplexer Circuit | 1:1 |
| Off-state Isolation-Nom | 55 dB |
| Current - Leakage (IS(off)) (Max) | 1μA |
| Channel Capacitance (CS(off), CD(off)) | 2pF |
| Switch Circuit | SPST - NO |
| Switch Time (Ton, Toff) (Max) | 1.4ns, 1.5ns |
| Switch-off Time-Max | 2.9ns |
| Voltage - Supply, Single (V+) | 0.8V~2.7V |
| Height | 1.45mm |
| Length | 2.9mm |
| Width | 1.6mm |
| Thickness | 1.2mm |
| RoHS Status | ROHS3 Compliant |
| Lead Free | Lead Free |
SN74AUC1G66DBVR Overview
Shipping overseas is convenient with the electronic component packed in SC-74A, SOT-753. This high-reliability packaging method uses advanced packaging methods Cut Tape (CT). Multiplexers like this are mounted in the Surface Mount position. Multiplexers and demultiplexers have a ratio of 1:1. Extended operating temperature around -40°C~85°C TA. In total, there have been 5 terminations. As a result of its 1 channels, this electronic component provides high-quality output. If the voltage supply is 1.65V volts, the electrical component should be turned on and run. Electronic part bodies are injected with 5 pins. A SPST - NO switching circuit is used for these analog switches. 74AUC1G66 can be used to search for analog multiplexer variants. Internally, this switch multiplexer has a resistance of 15Ohm. Datasheets for 5 pin functions are available upon request. It is normally recommended that users do not supply the multiplexer with voltages higher than 2.7V. Single supply type digital switch with a low cost. It is recommended to use 800mV as the lowest voltage for the electrical part. The switch device would be able to operate with 10μA current. A voltage of 0.8V~2.7V is required for this switch device, which drains from a single voltage source. It may damage the digital multiplexer if the voltage is higher than 10μA. The transfer of data can be performed over 170MHz bandwidths.
SN74AUC1G66DBVR Features
1 Channels
Switch Circuit: SPST - NO
10μA Supply Current
-3db Bandwidth: 50MHz
Bandwidth: 170MHz
SN74AUC1G66DBVR Applications
There are a lot of Texas Instruments SN74AUC1G66DBVR Analog Switches & Multiplexers ICs applications.
- Avionics test equipment
- Channel Banks
- Sample-and-hold systems
- Communications systems
- Industrial and process control systems
- Avionics
- Communication systems
- Fault Tolerant Systems
- Precision test equipment
- Multiplexers