SN74AS574DWG4
| Parameters | |
|---|---|
| Mount | Surface Mount |
| Package / Case | SOIC |
| Number of Pins | 20 |
| Weight | 500.709277mg |
| JESD-609 Code | e4 |
| Moisture Sensitivity Level (MSL) | 1 |
| Number of Terminations | 20 |
| Terminal Finish | Nickel/Palladium/Gold (Ni/Pd/Au) |
| Max Operating Temperature | 70°C |
| Min Operating Temperature | 0°C |
| Additional Feature | BROADSIDE VERSION OF 374 |
| Subcategory | FF/Latches |
| Packing Method | TUBE |
| Technology | TTL |
| Terminal Position | DUAL |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 260 |
| Number of Functions | 1 |
| Supply Voltage | 5V |
| Frequency | 90MHz |
| Time@Peak Reflow Temperature-Max (s) | NOT SPECIFIED |
| Pin Count | 20 |
| Qualification Status | Not Qualified |
| Output Type | TTL |
| Operating Supply Voltage | 5V |
| Number of Elements | 1 |
| Polarity | Non-Inverting |
| Power Supplies | 5V |
| Temperature Grade | COMMERCIAL |
| Max Supply Voltage | 5.5V |
| Min Supply Voltage | 4.5V |
| Load Capacitance | 50pF |
| Number of Ports | 2 |
| Current - Output | 48mA |
| Propagation Delay | 9 ns |
| Turn On Delay Time | 3 ns |
| Family | AS |
| Logic Function | D-Type, Flip-Flop |
| Output Characteristics | 3-STATE |
| Logic IC Type | BUS DRIVER |
| Number of Bits per Element | 8 |
| High Level Output Current | 48mA |
| Low Level Output Current | 48mA |
| Clock Edge Trigger Type | Positive Edge |
| Height Seated (Max) | 2.65mm |
| Width | 7.5mm |
| RoHS Status | RoHS Compliant |
| Lead Free | Lead Free |
SN74AS574DWG4 Overview
In the form of SOIC, it has been packaged. In the configuration, TTLis used as the output. The element count is 1 . A total of 20terminations have been recorded. The D flip flop is powered by a voltage of 5V . In this case, the D flip flop belongs to the ASfamily. There is an electronic part that is mounted in the way of Surface Mount. This board has 20 pins. There is a clock edge trigger type of Positive Edgeon this device. The part you are looking for is included in FF/Latches. In light of its reliable performance, this T flip flop is well suited for TUBE. The system runs on a power supply of 5V watts. There are 2 ports embedded in the flip flops. In order to achieve high efficiency, the supply voltage should be maintained at 5V. BROADSIDE VERSION OF 374is also one of its characteristics. A 48mAis set for the high level output current. There is 48mA output current at the low level. The operating temperature should be lower than 70°C. It is recommended that the operating temperature is higher than 0°C. The minimum voltage required for operation is 4.5V. There is a maximum supply voltage of 5.5V. It is possible to achieve 90MHz frequencies. There is a logic IC BUS DRIVER used in the D flip flop. It has 1 functions. There are 20 pins on the D latch. The 48mA output current allows it to be designed with the greatest amount of flexibility.
SN74AS574DWG4 Features
20 pins
5V power supplies
1 Functions
20 pin count
SN74AS574DWG4 Applications
There are a lot of Texas Instruments SN74AS574DWG4 Flip Flops applications.
- Asynchronous counter
- Test & Measurement
- Supports Live Insertion
- Communications
- Common Clocks
- Data Synchronizers
- Divide a clock signal by 2 or 4
- Guaranteed simultaneous switching noise level
- Matched Rise and Fall
- Event Detectors