SN74ALS273NSR
| Parameters | |
|---|---|
| Factory Lead Time | 6 Weeks |
| Lifecycle Status | ACTIVE (Last Updated: 3 days ago) |
| Mount | Surface Mount |
| Mounting Type | Surface Mount |
| Package / Case | 20-SOIC (0.209, 5.30mm Width) |
| Number of Pins | 20 |
| Weight | 266.712314mg |
| Operating Temperature | 0°C~70°C TA |
| Packaging | Tape & Reel (TR) |
| Series | 74ALS |
| JESD-609 Code | e4 |
| Pbfree Code | yes |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 20 |
| ECCN Code | EAR99 |
| Type | D-Type |
| Terminal Finish | Nickel/Palladium/Gold (Ni/Pd/Au) |
| Subcategory | FF/Latches |
| Packing Method | TR |
| Technology | TTL |
| Voltage - Supply | 4.5V~5.5V |
| Terminal Position | DUAL |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 260 |
| Supply Voltage | 5V |
| Time@Peak Reflow Temperature-Max (s) | NOT SPECIFIED |
| Base Part Number | 74ALS273 |
| Function | Master Reset |
| Qualification Status | Not Qualified |
| Output Type | Non-Inverted |
| Operating Supply Voltage | 5V |
| Number of Elements | 1 |
| Polarity | Non-Inverting |
| Power Supplies | 5V |
| Number of Circuits | 8 |
| Load Capacitance | 50pF |
| Output Current | 24mA |
| Number of Bits | 8 |
| Clock Frequency | 35MHz |
| Propagation Delay | 15 ns |
| Turn On Delay Time | 2 ns |
| Family | ALS |
| Logic Function | D-Type, Flip-Flop |
| Current - Quiescent (Iq) | 20mA |
| Current - Output High, Low | 2.6mA 24mA |
| Max I(ol) | 0.024 A |
| Max Propagation Delay @ V, Max CL | 15ns @ 5V, 50pF |
| Trigger Type | Positive Edge |
| Power Supply Current-Max (ICC) | 29mA |
| Number of Input Lines | 3 |
| Clock Edge Trigger Type | Positive Edge |
| Height | 2mm |
| Length | 12.6mm |
| Width | 5.3mm |
| Thickness | 1.95mm |
| RoHS Status | ROHS3 Compliant |
| Lead Free | Lead Free |
SN74ALS273NSR Overview
20-SOIC (0.209, 5.30mm Width)is the packaging method. D flip flop is embedded in the Tape & Reel (TR) package. In the configuration, Non-Invertedis used as the output. This trigger uses the value Positive Edge. There is an electric part mounted in the way of Surface Mount. The JK flip flop operates at 4.5V~5.5Vvolts. 0°C~70°C TAis the operating temperature. It belongs to the type D-Typeof flip flops. JK flip flop belongs to the 74ALSseries of FPGAs. You should not exceed 35MHzin the output frequency of the device. There are 1 elements in it. During its operation, it consumes 20mA quiescent energy. Currently, there are 20 terminations. D latch belongs to the 74ALS273 family. An input voltage of 5Vpowers the D latch. Electronic devices of this type belong to the ALSfamily. In this case, the electronic component is mounted in the way of Surface Mount. This board has 20 pins. In this device, the clock edge trigger type is Positive Edge. There is a FF/Latchesbase part number assigned to the RS flip flops. An electronic part with 8bits has been designed. The superior flexibility is achieved through the use of 8 circuits. This D flip flop is well suited for TR based on its reliable performance. The power supply is 5V. For high efficiency, the supply voltage should be set to 5V. This T flip flop features a maximum design flexibility due to its output current of 24mA. This input has 3lines.
SN74ALS273NSR Features
Tape & Reel (TR) package
74ALS series
20 pins
8 Bits
5V power supplies
SN74ALS273NSR Applications
There are a lot of Texas Instruments SN74ALS273NSR Flip Flops applications.
- Patented noise
- 2 – Bit synchronous counter
- Individual Asynchronous Resets
- Shift Registers
- Cold spare funcion
- Consumer
- Reduced system switching noise
- ATE
- Power down protection
- Functionally equivalent to the MC10/100EL29