SN74AHCT74RGYR
| Parameters | |
|---|---|
| Factory Lead Time | 6 Weeks |
| Lifecycle Status | ACTIVE (Last Updated: 4 days ago) |
| Mount | Surface Mount |
| Mounting Type | Surface Mount |
| Package / Case | 14-VFQFN Exposed Pad |
| Number of Pins | 14 |
| Weight | 32.205058mg |
| Operating Temperature | -40°C~125°C TA |
| Packaging | Cut Tape (CT) |
| Series | 74AHCT |
| JESD-609 Code | e4 |
| Pbfree Code | yes |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 2 (1 Year) |
| Number of Terminations | 14 |
| ECCN Code | EAR99 |
| Type | D-Type |
| Terminal Finish | Nickel/Palladium/Gold (Ni/Pd/Au) |
| Subcategory | FF/Latches |
| Packing Method | TR |
| Technology | CMOS |
| Voltage - Supply | 4.5V~5.5V |
| Terminal Position | QUAD |
| Terminal Form | NO LEAD |
| Peak Reflow Temperature (Cel) | 260 |
| Supply Voltage | 5V |
| Terminal Pitch | 0.5mm |
| Time@Peak Reflow Temperature-Max (s) | NOT SPECIFIED |
| Base Part Number | 74AHCT74 |
| Function | Set(Preset) and Reset |
| Qualification Status | Not Qualified |
| Output Type | Differential |
| Operating Supply Voltage | 5V |
| Polarity | Non-Inverting |
| Power Supplies | 5V |
| Number of Circuits | 2 |
| Load Capacitance | 50pF |
| Clock Frequency | 140MHz |
| Propagation Delay | 8.8 ns |
| Turn On Delay Time | 1 ns |
| Family | AHCT/VHCT/VT |
| Logic Function | AND, D-Type, Flip-Flop |
| Current - Quiescent (Iq) | 2μA |
| Current - Output High, Low | 8mA 8mA |
| Max I(ol) | 0.008 A |
| Number of Bits per Element | 1 |
| Max Propagation Delay @ V, Max CL | 8.8ns @ 5V, 50pF |
| Trigger Type | Positive Edge |
| Input Capacitance | 2pF |
| Number of Input Lines | 4 |
| fmax-Min | 80 MHz |
| Clock Edge Trigger Type | Positive Edge |
| Max Frequency@Nom-Sup | 65000000Hz |
| Height | 1mm |
| Length | 3.5mm |
| Width | 3.5mm |
| Thickness | 900μm |
| RoHS Status | ROHS3 Compliant |
| Lead Free | Lead Free |
SN74AHCT74RGYR Overview
In the form of 14-VFQFN Exposed Pad, it has been packaged. A package named Cut Tape (CT)includes it. T flip flop uses Differentialas its output configuration. The trigger configured with it uses Positive Edge. Surface Mountis occupied by this electronic component. A 4.5V~5.5Vsupply voltage is required for it to operate. A temperature of -40°C~125°C TAis used in the operation. It is an electronic flip flop with the type D-Type. In terms of FPGAs, it belongs to the 74AHCT series. You should not exceed 140MHzin its output frequency. As a result, it consumes 2μA quiescent current and is not affected by external forces. Currently, there are 14 terminations. D latch belongs to the 74AHCT74 family. Power is supplied from a voltage of 5V volts. A JK flip flop with a 2pFfarad input capacitance is used here. This D flip flop belongs to the family of AHCT/VHCT/VT. Surface Mount mounts this electronic component. The 14pins are designed into the board. In this device, the clock edge trigger type is Positive Edge. The part is included in FF/Latches. To achieve this superior flexibility, 2 circuits are used. As a result of its reliability, this D flip flop is ideally suited for TR. It runs on 5Vvolts of power. In order to ensure high efficiency, the supply voltage should remain at 5V. Currently, there are 4 lines of input.
SN74AHCT74RGYR Features
Cut Tape (CT) package
74AHCT series
14 pins
5V power supplies
SN74AHCT74RGYR Applications
There are a lot of Texas Instruments SN74AHCT74RGYR Flip Flops applications.
- Divide a clock signal by 2 or 4
- 2 – Bit synchronous counter
- Set-reset capability
- Reduced system switching noise
- Data Synchronizers
- CMOS Process
- QML qualified product
- Dynamic threshold performance
- Common Clocks
- Bus hold