SN74AHC4066RGYR
| Parameters | |
|---|---|
| Factory Lead Time | 6 Weeks |
| Lifecycle Status | ACTIVE (Last Updated: 2 days ago) |
| Mount | Surface Mount |
| Mounting Type | Surface Mount |
| Package / Case | 14-VFQFN Exposed Pad |
| Number of Pins | 14 |
| Weight | 32.205058mg |
| Operating Temperature | -40°C~85°C TA |
| Packaging | Cut Tape (CT) |
| JESD-609 Code | e4 |
| Pbfree Code | yes |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 2 (1 Year) |
| Number of Terminations | 14 |
| ECCN Code | EAR99 |
| Resistance | 75Ohm |
| Terminal Finish | Nickel/Palladium/Gold (Ni/Pd/Au) |
| Subcategory | Multiplexer or Switches |
| Technology | CMOS |
| Terminal Position | QUAD |
| Terminal Form | NO LEAD |
| Peak Reflow Temperature (Cel) | 260 |
| Number of Functions | 4 |
| Supply Voltage | 2.3V |
| Terminal Pitch | 0.5mm |
| Time@Peak Reflow Temperature-Max (s) | NOT SPECIFIED |
| Base Part Number | 74AHC4066 |
| Output | SEPARATE OUTPUT |
| Pin Count | 14 |
| Qualification Status | Not Qualified |
| Polarity | Non-Inverting |
| Power Supplies | 2.5/5V |
| Number of Channels | 4 |
| Max Supply Voltage | 5.5V |
| Min Supply Voltage | 2V |
| Max Supply Current | 20μA |
| Throw Configuration | SPST |
| Propagation Delay | 4 ns |
| Turn On Delay Time | 25 ns |
| Supply Type | Single |
| Bandwidth | 50MHz |
| Turn-Off Delay Time | 25 ns |
| On-State Resistance (Max) | 75Ohm |
| Multiplexer/Demultiplexer Circuit | 1:1 |
| Off-state Isolation-Nom | 40 dB |
| Current - Leakage (IS(off)) (Max) | 100nA |
| Channel Capacitance (CS(off), CD(off)) | 0.5pF 5.5pF |
| On-state Resistance Match-Nom | 6Ohm |
| Switch Circuit | SPST - NO |
| Switch Time (Ton, Toff) (Max) | 12ns, 12ns |
| Channel-to-Channel Matching (ΔRon) | 2 Ω |
| Crosstalk | -45dB @ 1MHz |
| Switching | BREAK-BEFORE-MAKE |
| Voltage - Supply, Single (V+) | 2V~5.5V |
| Normal Position | NO |
| Height | 1mm |
| Length | 3.5mm |
| Width | 3.5mm |
| Thickness | 900μm |
| RoHS Status | ROHS3 Compliant |
| Lead Free | Lead Free |
SN74AHC4066RGYR Overview
The electronic part can be shipped overseas conveniently because it is packaged in 14-VFQFN Exposed Pad. A high level of reliability can be achieved through the use of an advanced packaging method Cut Tape (CT). Mounted in Surface Mount is this multiplexer. In the multiplexer and demultiplexer, 1:1 represents the number of circuits. An extended operating temperature of -40°C~85°C TA degrees Celsius. The total number of terminations is 14. Due to its 4 channels, the electrical component produces high-quality output. When a voltage supply of 2.3V is used, the electronic component should be turned on and run. A total of 14 pins are injected into the electrical part body. A SPST - NO switching circuit is used for these analog switches. Look for analog switch ic variants by searching with 74AHC4066. Internally, this switch multiplexer has a resistance of 75Ohm. For functions related to 14 pins, please refer to the datasheets. A analogue multiplexer of this type is a Multiplexer or Switches. normally, users should not supply switches with voltages higher than 5.5V. A cost-effective Single supply type analogue multiplexer. 2V is the lowest voltage that should be fed to the electronic electronic part. The voltage required by this switch device is 2V~5.5V, draining from a single voltage supply. The analogue multiplexer may be damaged if voltage is greater than 20μA. A total of SEPARATE OUTPUT outputs are available on this analog switch ic. In 50MHz-bandwidths, data can be transferred.
SN74AHC4066RGYR Features
4 Channels
Switch Circuit: SPST - NO
Bandwidth: 50MHz
SN74AHC4066RGYR Applications
There are a lot of Texas Instruments SN74AHC4066RGYR Analog Switches & Multiplexers ICs applications.
- Battery-powered systems
- Signal routing between systems
- 65 V DACs
- Remote Powered Equipment
- Wireless Local Loop
- Microprocessor controlled systems
- Voice over IP/DSL – Integrated Access Devices, Smart
- Multi-Line E1 Interface Cards
- Data switching
- Central office