SN74AC74PWR
| Parameters | |
|---|---|
| Current - Output High, Low | 24mA 24mA |
| Number of Bits per Element | 1 |
| Max Propagation Delay @ V, Max CL | 6ns @ 5V, 50pF |
| Trigger Type | Positive Edge |
| Input Capacitance | 3pF |
| Number of Input Lines | 4 |
| Clock Edge Trigger Type | Positive Edge |
| Max Frequency@Nom-Sup | 95000000Hz |
| Height | 1.2mm |
| Length | 5mm |
| Width | 4.4mm |
| Thickness | 1mm |
| Radiation Hardening | No |
| RoHS Status | ROHS3 Compliant |
| Lead Free | Lead Free |
| Factory Lead Time | 6 Weeks |
| Lifecycle Status | ACTIVE (Last Updated: 6 days ago) |
| Contact Plating | Gold |
| Mount | Surface Mount |
| Mounting Type | Surface Mount |
| Package / Case | 14-TSSOP (0.173, 4.40mm Width) |
| Number of Pins | 14 |
| Weight | 57.209338mg |
| Operating Temperature | -40°C~85°C TA |
| Packaging | Cut Tape (CT) |
| Series | 74AC |
| JESD-609 Code | e4 |
| Pbfree Code | yes |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 14 |
| ECCN Code | EAR99 |
| Type | D-Type |
| Subcategory | FF/Latches |
| Packing Method | TR |
| Technology | CMOS |
| Voltage - Supply | 2V~6V |
| Terminal Position | DUAL |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 260 |
| Supply Voltage | 3V |
| Base Part Number | 74AC74 |
| Function | Set(Preset) and Reset |
| Output Type | Differential |
| Operating Supply Voltage | 5V |
| Polarity | Non-Inverting |
| Supply Voltage-Max (Vsup) | 6V |
| Supply Voltage-Min (Vsup) | 2V |
| Number of Channels | 2 |
| Load Capacitance | 50pF |
| Output Current | 24mA |
| Clock Frequency | 160MHz |
| Propagation Delay | 14 ns |
| Quiescent Current | 2μA |
| Turn On Delay Time | 6 ns |
| Family | AC |
| Logic Function | AND, D-Type, Flip-Flop |
SN74AC74PWR Overview
It is embeded in 14-TSSOP (0.173, 4.40mm Width) case. It is contained within the Cut Tape (CT)package. T flip flop uses Differentialas its output configuration. This trigger uses the value Positive Edge. There is an electric part mounted in the way of Surface Mount. A supply voltage of 2V~6V is required for operation. Temperature is set to -40°C~85°C TA. It is an electronic flip flop with the type D-Type. JK flip flop belongs to the 74ACseries of FPGAs. You should not exceed 160MHzin the output frequency of the device. A total of 14 terminations have been made. The 74AC74family includes it. A voltage of 3V is used as the power supply for this D latch. The input capacitance of this T flip flop is 3pF farads, which is defined as the capacitance between the input terminals of an op amp with either input grounded. A device of this type belongs to the family of AC. Surface Mount mounts this electronic component. The 14pins are designed into the board. A Positive Edgeclock edge trigger is used in this device. This device is part of the FF/Latchesbase part number family. 6Vis the maximum supply voltage (Vsup). Keeping the supply voltage (Vsup) above 2V is necessary for normal operation. As a result of its reliable performance, this T flip flop is suitable for TR. The supply voltage should be maintained at 5V for high efficiency. With a current output of 24mA , it offers maximum design flexibility. There are 4 input Lines, which consist of an electronic circuit connected between the ac mains and the rectifier input stage of the switching power supply. There is a consumption of 2μAof quiescent current from it. Currently, there are 2 channels available.
SN74AC74PWR Features
Cut Tape (CT) package
74AC series
14 pins
SN74AC74PWR Applications
There are a lot of Texas Instruments SN74AC74PWR Flip Flops applications.
- Test & Measurement
- EMI reduction circuitry
- Dynamic threshold performance
- Power down protection
- Count Modes
- Balanced 24 mA output drivers
- Pattern generators
- Load Control
- Divide a clock signal by 2 or 4
- Frequency division