SN74ABT823NT
| Parameters | |
|---|---|
| Mount | Through Hole |
| Mounting Type | Through Hole |
| Package / Case | 24-DIP (0.300, 7.62mm) |
| Number of Pins | 24 |
| Weight | 1.753503g |
| Operating Temperature | -40°C~85°C TA |
| Packaging | Tube |
| Series | 74ABT |
| JESD-609 Code | e4 |
| Pbfree Code | yes |
| Part Status | Obsolete |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 24 |
| Type | D-Type |
| Terminal Finish | Nickel/Palladium/Gold (Ni/Pd/Au) |
| Additional Feature | WITH CLEAR AND CLOCK ENABLE |
| Subcategory | FF/Latches |
| Technology | BICMOS |
| Voltage - Supply | 4.5V~5.5V |
| Terminal Position | DUAL |
| Supply Voltage | 5V |
| Terminal Pitch | 2.54mm |
| Base Part Number | 74ABT823 |
| Function | Master Reset |
| Output Type | Tri-State, Non-Inverted |
| Operating Supply Voltage | 5V |
| Number of Elements | 1 |
| Polarity | Non-Inverting |
| Power Supplies | 5V |
| Load Capacitance | 50pF |
| Number of Ports | 2 |
| Output Current | 64mA |
| Number of Bits | 9 |
| Clock Frequency | 200MHz |
| Propagation Delay | 6.1 ns |
| Turn On Delay Time | 4.3 ns |
| Family | ABT |
| Logic Function | D-Type, Flip-Flop |
| Current - Quiescent (Iq) | 250μA |
| Current - Output High, Low | 32mA 64mA |
| Max I(ol) | 0.064 A |
| Max Propagation Delay @ V, Max CL | 6.1ns @ 5V, 50pF |
| Trigger Type | Positive Edge |
| Input Capacitance | 4pF |
| Number of Input Lines | 9 |
| Number of Output Lines | 3 |
| Clock Edge Trigger Type | Positive Edge |
| Height Seated (Max) | 5.08mm |
| Width | 7.62mm |
| Radiation Hardening | No |
| REACH SVHC | No SVHC |
| RoHS Status | ROHS3 Compliant |
| Lead Free | Lead Free |
SN74ABT823NT Overview
The flip flop is packaged in 24-DIP (0.300, 7.62mm). D flip flop is embedded in the Tube package. Tri-State, Non-Invertedis the output configured for it. The trigger it is configured with uses Positive Edge. There is an electric part mounted in the way of Through Hole. The JK flip flop operates with an input voltage of 4.5V~5.5V volts. -40°C~85°C TAis the operating temperature. The type of this D latch is D-Type. In terms of FPGAs, it belongs to the 74ABT series. This D flip flop should not have a frequency greater than 200MHz. D latch consists of 1 elements. As a result, it consumes 250μA quiescent current. A total of 24terminations have been recorded. D latch belongs to the 74ABT823 family. A voltage of 5V is used as the power supply for this D latch. Its input capacitance is 4pFfarads. Devices in the ABTfamily are electronic devices. It is mounted in the way of Through Hole. A total of 24pins are provided on this board. A Positive Edgeclock edge trigger is used in this device. It is included in FF/Latches. An electronic part designed with 9bits is used in this application. A total of 5V power supplies are needed to run it. A total of 2ports are embedded in the D flip flop. Optimal efficiency requires a supply voltage of 5V. Featuring the maximum design flexibility, it has an output current of 64mA . In order for the chip to function, it has 3output lines. As of now, there are 9input lines. It is also characterized by WITH CLEAR AND CLOCK ENABLE.
SN74ABT823NT Features
Tube package
74ABT series
24 pins
9 Bits
5V power supplies
SN74ABT823NT Applications
There are a lot of Texas Instruments SN74ABT823NT Flip Flops applications.
- Functionally equivalent to the MC10/100EL29
- 2 – Bit synchronous counter
- Data transfer
- Set-reset capability
- Convert a momentary switch to a toggle switch
- Automotive
- Control circuits
- Common Clocks
- Bounce elimination switch
- Single Up Count-Control Line