SN74ABT574ADWRE4
| Parameters | |
|---|---|
| Lifecycle Status | ACTIVE (Last Updated: 1 week ago) |
| Mount | Surface Mount |
| Package / Case | SOIC |
| Number of Pins | 20 |
| Weight | 500.709277mg |
| Packaging | Tape & Reel (TR) |
| JESD-609 Code | e4 |
| Pbfree Code | yes |
| Moisture Sensitivity Level (MSL) | 1 |
| Number of Terminations | 20 |
| Terminal Finish | Nickel/Palladium/Gold (Ni/Pd/Au) |
| Max Operating Temperature | 85°C |
| Min Operating Temperature | -40°C |
| Subcategory | FF/Latches |
| Packing Method | TR |
| Technology | BICMOS |
| Terminal Position | DUAL |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 260 |
| Number of Functions | 1 |
| Supply Voltage | 5V |
| Frequency | 200MHz |
| Time@Peak Reflow Temperature-Max (s) | NOT SPECIFIED |
| Pin Count | 20 |
| Qualification Status | Not Qualified |
| Output Type | TTL |
| Operating Supply Voltage | 5V |
| Number of Elements | 1 |
| Polarity | Non-Inverting |
| Power Supplies | 5V |
| Temperature Grade | INDUSTRIAL |
| Max Supply Voltage | 5.5V |
| Min Supply Voltage | 4.5V |
| Load Capacitance | 50pF |
| Number of Ports | 2 |
| Current - Output | 64mA |
| Propagation Delay | 6.6 ns |
| Turn On Delay Time | 3.9 ns |
| Family | ABT |
| Logic Function | D-Type, Flip-Flop |
| Logic IC Type | BUS DRIVER |
| Max I(ol) | 0.064 A |
| Number of Bits per Element | 8 |
| High Level Output Current | -32mA |
| Low Level Output Current | 64mA |
| Control Type | ENABLE LOW |
| Number of Output Lines | 3 |
| Count Direction | UNIDIRECTIONAL |
| Clock Edge Trigger Type | Positive Edge |
| Height | 2.65mm |
| Length | 12.8mm |
| Width | 7.5mm |
| Thickness | 2.35mm |
| RoHS Status | RoHS Compliant |
| Lead Free | Lead Free |
SN74ABT574ADWRE4 Overview
In the form of SOIC, it has been packaged. As part of the package Tape & Reel (TR), it is embedded. Currently, the output is configured to use TTL. In total, there are 1 elements. There are 20 terminations, which are the practice of ending a transmission line with a device that matches the characteristic impedance of the line. A voltage of 5V is used as the power supply for this D latch. An electronic device belonging to the family ABTcan be found here. It is mounted in the way of Surface Mount. The electronic flip flop is designed with pins 20. A Positive Edgeclock edge trigger is used in this device. The part is included in FF/Latches. A reliable performance of this D flip flop makes it well suited for use in TR. A total of 5V power supplies are needed to run it. The D flip flop is embedded with 2ports. It is recommended that the supply voltage be kept at 5Vto maximize efficiency. The JK flip flop is with 3 output lines to operate. -32mAis set as the high level output current. It is set to 64mAfor low level output current. The operating temperature should be lower than 85°C. Ideally, the operating temperature should be greater than -40°C. The minimal supply voltage is 4.5V. It supports the maximal supply voltage of 5.5V. This can be achieved at a frequency of 200MHz. BUS DRIVERis used as the logic IC in this D flip flop. It is equipped with 1 Functions . A total of 20 pins are present on this device. It offers maximum design flexibility with its output current of 64mA.
SN74ABT574ADWRE4 Features
Tape & Reel (TR) package
20 pins
5V power supplies
1 Functions
20 pin count
SN74ABT574ADWRE4 Applications
There are a lot of Texas Instruments SN74ABT574ADWRE4 Flip Flops applications.
- Communications
- Single Up Count-Control Line
- Convert a momentary switch to a toggle switch
- QML qualified product
- Divide a clock signal by 2 or 4
- Dynamic threshold performance
- Clock pulse
- Storage registers
- Individual Asynchronous Resets
- ATE