SN74ABT374ADWR
| Parameters | |
|---|---|
| Factory Lead Time | 6 Weeks |
| Lifecycle Status | ACTIVE (Last Updated: 5 days ago) |
| Mount | Surface Mount |
| Mounting Type | Surface Mount |
| Package / Case | 20-SOIC (0.295, 7.50mm Width) |
| Number of Pins | 20 |
| Weight | 500.709277mg |
| Operating Temperature | -40°C~85°C TA |
| Packaging | Cut Tape (CT) |
| Series | 74ABT |
| JESD-609 Code | e4 |
| Pbfree Code | yes |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 20 |
| ECCN Code | EAR99 |
| Type | D-Type |
| Terminal Finish | Nickel/Palladium/Gold (Ni/Pd/Au) |
| Subcategory | FF/Latches |
| Packing Method | TR |
| Technology | BICMOS |
| Voltage - Supply | 4.5V~5.5V |
| Terminal Position | DUAL |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 260 |
| Supply Voltage | 5V |
| Base Part Number | 74ABT374 |
| Function | Standard |
| Output Type | Tri-State, Non-Inverted |
| Operating Supply Voltage | 5V |
| Number of Elements | 1 |
| Polarity | Non-Inverting |
| Power Supplies | 5V |
| Number of Circuits | 8 |
| Load Capacitance | 50pF |
| Number of Ports | 2 |
| Output Current | 64mA |
| Number of Bits | 8 |
| Clock Frequency | 200MHz |
| Propagation Delay | 7.1 ns |
| Turn On Delay Time | 4.2 ns |
| Family | ABT |
| Logic Function | D-Type, Flip-Flop |
| Current - Quiescent (Iq) | 250μA |
| Current - Output High, Low | 32mA 64mA |
| Max I(ol) | 0.064 A |
| Max Propagation Delay @ V, Max CL | 5.1ns @ 5V, 50pF |
| Trigger Type | Positive Edge |
| Input Capacitance | 3.5pF |
| Number of Output Lines | 3 |
| Count Direction | UNIDIRECTIONAL |
| Clock Edge Trigger Type | Positive Edge |
| Height | 2.65mm |
| Length | 12.8mm |
| Width | 7.5mm |
| Thickness | 2.35mm |
| Radiation Hardening | No |
| RoHS Status | ROHS3 Compliant |
| Lead Free | Lead Free |
SN74ABT374ADWR Overview
In the form of 20-SOIC (0.295, 7.50mm Width), it has been packaged. The Cut Tape (CT)package contains it. T flip flop uses Tri-State, Non-Invertedas its output configuration. There is a trigger configured with Positive Edge. In this case, the electronic component is mounted in the way of Surface Mount. Powered by a 4.5V~5.5Vvolt supply, it operates as follows. It is operating at -40°C~85°C TA. Logic flip flops of this type are classified as D-Type. JK flip flop is a part of the 74ABTseries of FPGAs. Its output frequency should not exceed 200MHz Hz. There are 1 elements in it. It consumes 250μA of quiescent A total of 20terminations have been recorded. The 74ABT374 family contains it. A voltage of 5V is used to power it. This T flip flop has a capacitance of 3.5pF farads at the input. This D flip flop belongs to the family of ABT. This electronic part is mounted in the way of Surface Mount. A total of 20pins are provided on this board. This device's clock edge trigger type is Positive Edge. The part you are looking for is included in FF/Latches. 8bits are used in its design. Its superior flexibility is attributed to its use of 8 circuits. In view of its reliability, this D flip flop is a good fit for TR. The power supply is 5V. The flip flop contains 2ports. High efficiency requires the supply voltage to be maintained at 5V. With a current output of 64mA , it offers maximum design flexibility. It has 3 output lines to operate.
SN74ABT374ADWR Features
Cut Tape (CT) package
74ABT series
20 pins
8 Bits
5V power supplies
SN74ABT374ADWR Applications
There are a lot of Texas Instruments SN74ABT374ADWR Flip Flops applications.
- Storage registers
- Safety Clamp
- Reduced system switching noise
- High Performance Logic for test systems
- Registers
- Single Down Count-Control Line
- Balanced Propagation Delays
- EMI reduction circuitry
- Digital electronics systems
- Matched Rise and Fall