OPA4704EA/250
| Parameters | |
|---|---|
| Factory Lead Time | 6 Weeks |
| Lifecycle Status | ACTIVE (Last Updated: 5 days ago) |
| Contact Plating | Gold |
| Mounting Type | Surface Mount |
| Package / Case | 14-TSSOP (0.173, 4.40mm Width) |
| Surface Mount | YES |
| Number of Pins | 14 |
| Operating Temperature | -40°C~85°C |
| Packaging | Tape & Reel (TR) |
| JESD-609 Code | e4 |
| Pbfree Code | yes |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 2 (1 Year) |
| Number of Terminations | 14 |
| ECCN Code | EAR99 |
| Subcategory | Operational Amplifier |
| Packing Method | TR |
| Technology | CMOS |
| Terminal Position | DUAL |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 260 |
| Number of Functions | 4 |
| Supply Voltage | 5V |
| Base Part Number | OPA4704 |
| Pin Count | 14 |
| Output Type | Rail-to-Rail |
| Operating Supply Voltage | 6V |
| Number of Elements | 4 |
| Nominal Supply Current | 800μA |
| Output Current | 10mA |
| Current - Supply | 160μA |
| Slew Rate | 3V/μs |
| Architecture | VOLTAGE-FEEDBACK |
| Amplifier Type | General Purpose |
| Common Mode Rejection Ratio | 80 dB |
| Current - Input Bias | 1pA |
| Voltage - Supply, Single/Dual (±) | 4V~12V ±2V~6V |
| Input Offset Voltage (Vos) | 750μV |
| Bandwidth | 3MHz |
| Neg Supply Voltage-Nom (Vsup) | -5V |
| Unity Gain BW-Nom | 3000 kHz |
| Voltage Gain | 120dB |
| Average Bias Current-Max (IIB) | 0.00001μA |
| Power Supply Rejection Ratio (PSRR) | 93.98dB |
| Low-Offset | YES |
| Frequency Compensation | YES AVCL>=5 |
| Voltage - Input Offset | 160μV |
| Low-Bias | YES |
| Micropower | YES |
| Bias Current-Max (IIB) @25C | 0.00001μA |
| Programmable Power | NO |
| Nominal Gain Bandwidth Product | 3MHz |
| Max I/O Voltage | 750μV |
| Input Offset Current-Max (IIO) | 0.00001μA |
| Height | 1.2mm |
| Length | 5mm |
| Width | 4.4mm |
| Thickness | 1mm |
| Radiation Hardening | No |
| RoHS Status | ROHS3 Compliant |
| Lead Free | Lead Free |
OPA4704EA/250 Overview
There is a 14-TSSOP (0.173, 4.40mm Width) case package that contains the instrumentation amplifiers. This is a General Purpose type op amp. The case in which buffer amplifier is delivered is called a Tape & Reel (TR) case. It is estimated that there will be 14 terminations in the next few months. A total of 14 pins are located on this board. I would like to remind you that this buffer op amp should be powered by an 5V battery. To be specific, this instrumentation amplifier is a type of Operational Amplifier. 14 pins are included on the operational amplifiers. Op amp rates 750μV as input offset voltage. Surface Mount is the recommended mounting type of operational amplifiers. It is important to note that this linear amplifier works well at a temperature of -40°C~85°C when it comes to operating temperatureMaintain 120dB as the voltage gain. As one of the many benefits of this buffer amplifier, it puts out Rail-to-Rail signals, which is one of the many benefits it offers. According to the specifications of the buffer op amp, the operating supply voltage is rated at 4. The operating supply voltage of the buffer op amp is rated at 6V. As a result of this, the buffer amplifier is packed in TR. As a recommendation, this electronic component should be used with a power supply that can deliver 160μA.
OPA4704EA/250 Features
14 Pins
supply voltage of 5V
120dB voltage gain
Output Type: Rail-to-Rail
OPA4704EA/250 Applications
There are a lot of Texas Instruments OPA4704EA/250 Instrumentational OP Amps applications.
- Band-pass filter
- Fission chambers
- Laptop
- Strain gauges
- ECG equipment
- Multimedia playback equipment
- Navigation
- PDA
- Polarized electrodes
- MP3