OPA4314AIPW
| Parameters | |
|---|---|
| Factory Lead Time | 6 Weeks |
| Lifecycle Status | ACTIVE (Last Updated: 6 days ago) |
| Contact Plating | Gold |
| Mount | Surface Mount |
| Mounting Type | Surface Mount |
| Package / Case | 14-TSSOP (0.173, 4.40mm Width) |
| Number of Pins | 14 |
| Operating Temperature | -40°C~125°C |
| Packaging | Bulk |
| JESD-609 Code | e4 |
| Pbfree Code | yes |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 2 (1 Year) |
| Number of Terminations | 14 |
| ECCN Code | EAR99 |
| Subcategory | Operational Amplifier |
| Packing Method | TUBE |
| Technology | CMOS |
| Terminal Position | DUAL |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 260 |
| Number of Functions | 4 |
| Supply Voltage | 5V |
| Base Part Number | OPA4314 |
| Pin Count | 14 |
| Output Type | Rail-to-Rail |
| Number of Elements | 4 |
| Power Supplies | +-0.9/+-2.75/1.8/5.5V |
| Operating Supply Current | 150μA |
| Nominal Supply Current | 150μA |
| Output Current | 20mA |
| Slew Rate | 1.5V/μs |
| Architecture | VOLTAGE-FEEDBACK |
| Amplifier Type | General Purpose |
| Common Mode Rejection Ratio | 66 dB |
| Current - Input Bias | 0.2pA |
| Voltage - Supply, Single/Dual (±) | 1.8V~5.5V ±0.9V~2.75V |
| Output Current per Channel | 20mA |
| Input Offset Voltage (Vos) | 2.5mV |
| Unity Gain BW-Nom | 3000 kHz |
| Voltage Gain | 128dB |
| Average Bias Current-Max (IIB) | 0.006μA |
| Power Supply Rejection Ratio (PSRR) | 78dB |
| Low-Offset | NO |
| Frequency Compensation | YES |
| Supply Voltage Limit-Max | 7V |
| Voltage - Input Offset | 500μV |
| Low-Bias | YES |
| Micropower | YES |
| Max Frequency | 3MHz |
| Bias Current-Max (IIB) @25C | 0.00001μA |
| Programmable Power | NO |
| Wideband | NO |
| Input Offset Current-Max (IIO) | 0.00001μA |
| Height | 1.2mm |
| Length | 5mm |
| Width | 4.4mm |
| Thickness | 1mm |
| Radiation Hardening | No |
| RoHS Status | ROHS3 Compliant |
| Lead Free | Lead Free |
OPA4314AIPW Overview
The linear amplifier is packaged in a 14-TSSOP (0.173, 4.40mm Width) case which makes it easy for the consumer to handle. General Purpose-type instrumentation amplifiers are used in this application. As far as the packaging is concerned, buffer op amp is delivered in a Bulk case. A total of 14 terminations have been reported in the past few weeks. The total number of pins on linear amplifier is 14. It would be helpful if you could remember that this op amp ic should be powered by an 5V battery. To be specific, this instrumentation amplifier is a type of Operational Amplifier. There are 14 pins on this chip. With regards to the offset voltage of the input, buffer amplifier is rated at 2.5mV. This electronic component is recommended to be mounted using the mounting type Surface Mount. In terms of operating temperatures, this buffer amplifier works very well at a temperature of around -40°C~125°C . It is possible to operate this buffer amplifier from a supply current of 150μA . It is recommended to keep the voltage gain at 128dB at all times. Buffer amplifier produces Rail-to-Rail signals, which is one of its many benefits. A total of 4 elements are present in this linear amplifier. A TUBE-shaped amplifier is used to pack the buffer amps.
OPA4314AIPW Features
14 Pins
supply voltage of 5V
128dB voltage gain
Output Type: Rail-to-Rail
OPA4314AIPW Applications
There are a lot of Texas Instruments OPA4314AIPW Instrumentational OP Amps applications.
- Navigation
- Portable electronic products powered by batteries
- PDA
- pH (acidity)
- Radiation thermometry transducers
- Biopotential
- High/low-pass filter circuit
- Weak signal detection
- Strain gauges
- Signal filtering