OPA347PA
| Parameters | |
|---|---|
| Factory Lead Time | 6 Weeks |
| Lifecycle Status | ACTIVE (Last Updated: 5 days ago) |
| Mounting Type | Through Hole |
| Package / Case | 8-DIP (0.300, 7.62mm) |
| Surface Mount | NO |
| Number of Pins | 8 |
| Operating Temperature | -55°C~125°C |
| Packaging | Tube |
| JESD-609 Code | e4 |
| Pbfree Code | yes |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 8 |
| ECCN Code | EAR99 |
| Terminal Finish | Nickel/Palladium/Gold (Ni/Pd/Au) |
| Subcategory | Operational Amplifier |
| Technology | CMOS |
| Terminal Position | DUAL |
| Number of Functions | 1 |
| Supply Voltage | 5V |
| Terminal Pitch | 2.54mm |
| Base Part Number | OPA347 |
| Pin Count | 8 |
| Output Type | Rail-to-Rail |
| Power Supplies | 3/5V |
| Number of Channels | 1 |
| Operating Supply Current | 20μA |
| Nominal Supply Current | 34μA |
| Slew Rate | 0.17V/μs |
| Architecture | VOLTAGE-FEEDBACK |
| Amplifier Type | General Purpose |
| Common Mode Rejection Ratio | 70 dB |
| Current - Input Bias | 0.5pA |
| Voltage - Supply, Single/Dual (±) | 2.3V~5.5V ±1.15V~2.75V |
| Output Current per Channel | 17mA |
| Input Offset Voltage (Vos) | 6mV |
| Bandwidth | 350 kHz |
| Unity Gain BW-Nom | 350 kHz |
| Voltage Gain | 115dB |
| Power Supply Rejection Ratio (PSRR) | 84.44dB |
| Low-Offset | NO |
| Frequency Compensation | YES |
| Supply Voltage Limit-Max | 7.5V |
| Voltage - Input Offset | 2mV |
| Low-Bias | YES |
| Micropower | YES |
| Programmable Power | NO |
| Nominal Gain Bandwidth Product | 350 kHz |
| Max I/O Voltage | 6mV |
| Height | 5.08mm |
| Length | 9.81mm |
| Width | 6.35mm |
| Thickness | 3.9mm |
| Radiation Hardening | No |
| REACH SVHC | No SVHC |
| RoHS Status | ROHS3 Compliant |
| Lead Free | Lead Free |
OPA347PA Overview
A 8-DIP (0.300, 7.62mm) case is used to package the op amp. Buffer amps of this type are called General Purpose-types. A Tube case is used for delivering the op amp. The number of terminations approaches 8. The total number of pins on linear amplifier is 8. Please take in mind that this instrumentation amplifier should be run at 5V. It should be noted that this op amp is a type of Operational Amplifier device. There are 8 pins on this chip. Op amp ic rates 6mV for input offset voltage. Through Hole is the recommended mounting type of operational amplifiers. With regard to operating temperature, op amp ranges -55°C~125°C. Using a supply current of 20μA , this buffer op amp will be able to operate. Voltage gain should remain at 115dB. On the buffer amps, there are 1 channels that can be used. A benefit of this op amp ic is that it outputs Rail-to-Rail signals, which is one of the many advantages it has to offer.
OPA347PA Features
8 Pins
supply voltage of 5V
115dB voltage gain
Output Type: Rail-to-Rail
OPA347PA Applications
There are a lot of Texas Instruments OPA347PA Instrumentational OP Amps applications.
- Signal transformation
- Voltage regulation circuit
- Automatic control
- earphone
- High gain DC amplifier
- Non-polarized electrodes
- Signal amplification
- Thermocouples
- High/low-pass filter circuit
- Navigation