OPA211MDGKTEP
| Parameters | |
|---|---|
| Packing Method | TR |
| Technology | BIPOLAR |
| Terminal Position | DUAL |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 260 |
| Number of Functions | 1 |
| Supply Voltage | 15V |
| Terminal Pitch | 0.65mm |
| Base Part Number | OPA211 |
| Pin Count | 8 |
| Output Type | Rail-to-Rail |
| Number of Circuits | 1 |
| Operating Supply Current | 3.6mA |
| Nominal Supply Current | 3.6mA |
| Slew Rate | 27V/μs |
| Architecture | VOLTAGE-FEEDBACK |
| Amplifier Type | General Purpose |
| Common Mode Rejection Ratio | 108 dB |
| Current - Input Bias | 50nA |
| Max Input Voltage | 500mV |
| Voltage - Supply, Single/Dual (±) | 4.5V~36V ±2.25V~18V |
| Output Current per Channel | 30mA |
| Input Offset Voltage (Vos) | 20μV |
| Gain Bandwidth Product | 80MHz |
| Neg Supply Voltage-Nom (Vsup) | -15V |
| Unity Gain BW-Nom | 45000 kHz |
| Voltage Gain | 114dB |
| Power Supply Rejection Ratio (PSRR) | 140dB |
| Low-Offset | YES |
| Frequency Compensation | YES |
| Supply Voltage Limit-Max | 20V |
| Low-Bias | NO |
| Micropower | NO |
| Bias Current-Max (IIB) @25C | 0.2μA |
| Programmable Power | NO |
| Neg Supply Voltage-Max (Vsup) | -20V |
| Wideband | YES |
| Height | 1.07mm |
| Length | 3mm |
| Width | 3mm |
| Thickness | 970μm |
| Radiation Hardening | No |
| RoHS Status | ROHS3 Compliant |
| Lead Free | Lead Free |
| Factory Lead Time | 6 Weeks |
| Lifecycle Status | ACTIVE (Last Updated: 1 week ago) |
| Contact Plating | Gold |
| Mount | Surface Mount |
| Mounting Type | Surface Mount |
| Package / Case | 8-TSSOP, 8-MSOP (0.118, 3.00mm Width) |
| Number of Pins | 8 |
| Operating Temperature | -55°C~125°C |
| Packaging | Tape & Reel (TR) |
| JESD-609 Code | e4 |
| Pbfree Code | yes |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 2 (1 Year) |
| Number of Terminations | 8 |
| ECCN Code | EAR99 |
| Subcategory | Operational Amplifier |
OPA211MDGKTEP Overview
Packaged in a 8-TSSOP, 8-MSOP (0.118, 3.00mm Width) case, the buffer op amp is ready to use. An op amp ic of the General Purpose type. Linear amplifier is delivered in a Tape & Reel (TR) case. A total of 8 terminations have been reported in the past few weeks. Buffer amplifier has a total of 8 pins on it. I would like to remind you that this buffer op amp should be powered by an 15V battery. A type of Operational Amplifier buffer op amp is what this device is specifically, to be more precise. An 8-pin op amp ic is included in the package. The input offset voltage is 20μV. Surface Mount is the recommended mounting type for this linear amplifier. According to the manufacturer, this buffer op amp works well at -55°C~125°C , which is a good operating temperature. This op amp can operate from a supply current at 3.6mA. 114dB should be the voltage gain. A linear amplifier like this has 1 circuits on it. One of its many advantages is that buffer op amp outputs Rail-to-Rail signals. As a result of this, the buffer amplifier is packed in TR.
OPA211MDGKTEP Features
8 Pins
supply voltage of 15V
114dB voltage gain
Output Type: Rail-to-Rail
OPA211MDGKTEP Applications
There are a lot of Texas Instruments OPA211MDGKTEP Instrumentational OP Amps applications.
- Television
- Commercial audio systems
- Portable media players
- Subtraction operation circuits
- Broadcasting
- Vehicle electronics
- Micro signal measurement
- Exponential operation circuits
- Multimedia playback equipment
- High input resistance broadband