OP27EZ
| Parameters | |
|---|---|
| Factory Lead Time | 10 Weeks |
| Lifecycle Status | PRODUCTION (Last Updated: 3 weeks ago) |
| Contact Plating | Lead, Tin |
| Mounting Type | Through Hole |
| Package / Case | 8-CDIP (0.300, 7.62mm) |
| Surface Mount | NO |
| Number of Pins | 8 |
| Operating Temperature | -25°C~85°C |
| Packaging | Tube |
| JESD-609 Code | e0 |
| Pbfree Code | no |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 8 |
| ECCN Code | EAR99 |
| Terminal Finish | Tin/Lead (Sn63Pb37) |
| Subcategory | Operational Amplifier |
| Technology | BIPOLAR |
| Terminal Position | DUAL |
| Number of Functions | 1 |
| Supply Voltage | 15V |
| Terminal Pitch | 2.54mm |
| Base Part Number | OP27 |
| Pin Count | 8 |
| Number of Channels | 1 |
| Operating Supply Current | 5.7mA |
| Nominal Supply Current | 3mA |
| Quiescent Current | 5.7mA |
| Slew Rate | 2.8V/μs |
| Architecture | VOLTAGE-FEEDBACK |
| Amplifier Type | General Purpose |
| Common Mode Rejection Ratio | 120 dB |
| Current - Input Bias | 10nA |
| Voltage - Supply, Single/Dual (±) | ±4V~18V |
| Input Offset Voltage (Vos) | 25μV |
| Bandwidth | 8MHz |
| Neg Supply Voltage-Nom (Vsup) | -15V |
| Unity Gain BW-Nom | 8000 kHz |
| Voltage Gain | 125.11dB |
| Average Bias Current-Max (IIB) | 0.06μA |
| Power Supply Rejection Ratio (PSRR) | 114dB |
| Low-Offset | YES |
| Frequency Compensation | YES |
| Supply Voltage Limit-Max | 22V |
| Voltage - Input Offset | 10μV |
| Bias Current-Max (IIB) @25C | 0.04μA |
| Neg Supply Voltage-Max (Vsup) | -22V |
| Input Voltage Noise Density | 3.5nV/sqrt Hz |
| Height | 3.56mm |
| Length | 10.29mm |
| Width | 7.87mm |
| Radiation Hardening | No |
| REACH SVHC | No SVHC |
| RoHS Status | Non-RoHS Compliant |
| Lead Free | Contains Lead |
OP27EZ Overview
Packaged in a 8-CDIP (0.300, 7.62mm) case, the buffer op amp is ready to use. General Purpose-type instrumentation amplifiers are used in this application. In the case of Tube cases, linear amplifier will be delivered. It is estimated that there will be 8 terminations in the next few months. Buffer amplifier has a total of 8 pins. It is important to remember that this op amp should be operated at a voltage of 15V volts. To be specific, this instrumentation amplifier is a type of Operational Amplifier. In total, the buffer amplifier consists of 8 pins. In terms of input offset voltage, operational amplifier rates 25μV. This electronic part is recommended for mounting type Through Hole. In terms of operating temperature, this instrumentation amplifier performs well at a temperature of about -25°C~85°C . In order for this instrumentation amplifier to operate, the supply current needs to be between 5.7mA and 10 . Maintain 125.11dB as the voltage gain. There are 1 channels on the operational amplifiers. There is an 5.7mA quiescent current running through op amp ic.
OP27EZ Features
8 Pins
supply voltage of 15V
125.11dB voltage gain
OP27EZ Applications
There are a lot of Analog Devices Inc. OP27EZ Instrumentational OP Amps applications.
- Video amplifiers
- PDA
- Broadcasting
- Communication
- Comparator
- Video computer boards
- Mobile phone
- Radar
- Information processing
- Band-stop filter