NLX2G66DMUTAG
| Parameters | |
|---|---|
| Factory Lead Time | 2 Weeks |
| Lifecycle Status | ACTIVE (Last Updated: 1 day ago) |
| Mounting Type | Surface Mount |
| Package / Case | 8-UFDFN |
| Surface Mount | YES |
| Number of Pins | 8 |
| Operating Temperature | -55°C~125°C TA |
| Packaging | Tape & Reel (TR) |
| Published | 2013 |
| JESD-609 Code | e4 |
| Pbfree Code | yes |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 8 |
| Resistance | 5.5Ohm |
| Terminal Finish | Nickel/Palladium/Gold (Ni/Pd/Au) |
| Subcategory | Multiplexer or Switches |
| Technology | CMOS |
| Terminal Position | DUAL |
| Number of Functions | 2 |
| Supply Voltage | 1.8V |
| Terminal Pitch | 0.5mm |
| Output | SEPARATE OUTPUT |
| Pin Count | 8 |
| Number of Channels | 1 |
| Max Supply Voltage | 5.5V |
| Min Supply Voltage | 1.65V |
| Analog IC - Other Type | DIFFERENTIAL MULTIPLEXER |
| Max Supply Current | 1μA |
| Turn On Delay Time | 4.9 ns |
| Number of Inputs | 2 |
| Halogen Free | Halogen Free |
| Supply Type | Single |
| Turn-Off Delay Time | 6 ns |
| -3db Bandwidth | 270MHz |
| On-State Resistance (Max) | 5.5Ohm |
| Multiplexer/Demultiplexer Circuit | 1:1 |
| Off-state Isolation-Nom | 60 dB |
| Current - Leakage (IS(off)) (Max) | 100nA |
| Channel Capacitance (CS(off), CD(off)) | 6pF |
| On-state Resistance Match-Nom | 8Ohm |
| Switch Circuit | SPST - NO |
| Switch Time (Ton, Toff) (Max) | 4.9ns, 6ns |
| Channel-to-Channel Matching (ΔRon) | 4.5 Ω |
| Crosstalk | -100dB @ 1MHz |
| Switch-on Time-Max | 10ns |
| Voltage - Supply, Single (V+) | 1.65V~5.5V |
| Normal Position | NO |
| Height Seated (Max) | 0.55mm |
| Length | 1.95mm |
| Radiation Hardening | No |
| RoHS Status | ROHS3 Compliant |
| Lead Free | Lead Free |
NLX2G66DMUTAG Overview
The electronic component is convenient to ship overseas because it is packed in a 8-UFDFN. This high-reliability packaging method uses advanced packaging methods Tape & Reel (TR). It is mounted in the position Surface Mount. The ratio between the number of multiplexer and demultiplexer circuits is 1:1. Operating temperature around -55°C~125°C TA extended. A total of 8 terminations have been recorded. High-quality output is provided by the electronic component's 1 channels. A 1.8V voltage supply should turn on and run the electronic component. An electrical component of this type can be found in the 8 series. Circuits based on SPST - NO switching are used to construct these analog switch ics. It has an internal resistance of 5.5Ohm. You can find the functions of the 8 pins in the datasheets. The analog multiplexer shown here is a typical Multiplexer or Switches. In normalcircumstances, users should not exceed 5.5V volts for the multiplexer. Analogue multiplexer with a Single supply type that is cost-effective. The lowest voltage fed to the electronic component should be 1.65V. Draining from a single voltage supply, this analog switch requires a voltage of 1.65V~5.5V. Put voltage above 1μA on the multiplexer to cause damage. With a DIFFERENTIAL MULTIPLEXER analog IC integrated into the board. It is possible to use SEPARATE OUTPUT outputs on this digital multiplexer. Operating the 2 inputs requires 2 inputs.
NLX2G66DMUTAG Features
1 Channels
Switch Circuit: SPST - NO
-3db Bandwidth: 270MHz
NLX2G66DMUTAG Applications
There are a lot of ON Semiconductor NLX2G66DMUTAG Analog Switches & Multiplexers ICs applications.
- Automatic test equipment
- High reliability control systems
- Signal routing between systems
- ISDN NT1/TA
- ADCs such as AD7840/8, AD7870/1/2/4/5/6/8
- Voice over IP/DSL – Integrated Access Devices, Smart
- MP3 players
- Medical systems
- SONET/SDH ADM
- Fiber In The Loop (FITL)