NLAS5213AMUTAG
| Parameters | |
|---|---|
| Factory Lead Time | 14 Weeks |
| Lifecycle Status | LAST SHIPMENTS (Last Updated: 2 days ago) |
| Mounting Type | Surface Mount |
| Package / Case | 8-UFDFN |
| Surface Mount | YES |
| Number of Pins | 8 |
| Operating Temperature | -40°C~85°C TA |
| Packaging | Tape & Reel (TR) |
| Published | 2009 |
| JESD-609 Code | e4 |
| Pbfree Code | yes |
| Part Status | Obsolete |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 8 |
| Resistance | 1.3Ohm |
| Terminal Finish | Nickel/Palladium/Gold (Ni/Pd/Au) |
| Subcategory | Multiplexer or Switches |
| Terminal Position | DUAL |
| Number of Functions | 1 |
| Supply Voltage | 3.3V |
| Terminal Pitch | 0.4mm |
| Base Part Number | NLAS5213 |
| Pin Count | 8 |
| Operating Supply Voltage | 3V |
| Number of Channels | 1 |
| Number of Circuits | 1 |
| Max Supply Voltage | 4.5V |
| Min Supply Voltage | 1.65V |
| Operating Supply Current | 1μA |
| Throw Configuration | DPST |
| Turn On Delay Time | 20 ns |
| Number of Inputs | 2 |
| Halogen Free | Halogen Free |
| Supply Type | Single |
| Turn-Off Delay Time | 15 ns |
| -3db Bandwidth | 496MHz |
| On-State Resistance (Max) | 1.3Ohm |
| Multiplexer/Demultiplexer Circuit | 2:1 |
| Off-state Isolation-Nom | 57 dB |
| Channel Capacitance (CS(off), CD(off)) | 19pF |
| On-state Resistance Match-Nom | 0.16Ohm |
| Switch Circuit | DPST - NO |
| Switch Time (Ton, Toff) (Max) | 20ns, 15ns |
| Channel-to-Channel Matching (ΔRon) | 150m Ω |
| Crosstalk | -97dB @ 1MHz |
| Switching | BREAK-BEFORE-MAKE |
| Voltage - Supply, Single (V+) | 1.65V~4.5V |
| Height Seated (Max) | 0.55mm |
| Radiation Hardening | No |
| RoHS Status | RoHS Compliant |
| Lead Free | Lead Free |
NLAS5213AMUTAG Overview
The electronic part can be shipped overseas conveniently because it is packaged in 8-UFDFN. This high-reliability packaging method uses advanced packaging methods Tape & Reel (TR). This analog switch is mounted in Surface Mount. There is 2:1 ratio between the number of multiplexers and demultiplexers. Operational temperature extended around -40°C~85°C TA. There are 8 terminations totally. The electronic part provides high-quality output because it has 1 channels. When a voltage supply of 3.3V is used, the electronic component should be turned on and run. Into the electrical component body are injected 8 pins. Unlike digital switches, these are based on DPST - NO switching circuits. Circuits number 1 make up this analogue multiplexer. Try searching with NLAS5213 if you're looking for variants. A 1.3Ohm internal resistance characterizes this multiplexer. The datasheets for the 8 pins explain the functions. Multiplexer or Switches is a typical switch device. A voltage higher than 4.5V should not normally be supplied to the switches. The analog switch ic is of the Single supply type and is cost-effective. It is recommended to use 1.65V as the lowest voltage for the electrical part. It would be sufficient to run this analogue multiplexer with 1μA current. Using a single voltage supply, this switch device consumes 1.65V~4.5V volts. 3V operating voltages are supported by the electronic component. It is possible to operate 2 inputs.
NLAS5213AMUTAG Features
1 Channels
Switch Circuit: DPST - NO
1μA Supply Current
-3db Bandwidth: 496MHz
NLAS5213AMUTAG Applications
There are a lot of ON Semiconductor NLAS5213AMUTAG Analog Switches & Multiplexers ICs applications.
- HDTV
- Power routing
- Industrial and process control systems
- E1 Multiplexer
- Avionics test equipment
- Precision instrumentation
- Central office
- Modems
- SDH
- Communication systems