NLAS4684MNR2
| Parameters | |
|---|---|
| Lifecycle Status | OBSOLETE (Last Updated: 4 days ago) |
| Mounting Type | Surface Mount |
| Package / Case | 10-VFDFN Exposed Pad |
| Surface Mount | YES |
| Number of Pins | 10 |
| Operating Temperature | -55°C~125°C TA |
| Packaging | Tape & Reel (TR) |
| Published | 2008 |
| JESD-609 Code | e0 |
| Pbfree Code | no |
| Part Status | Obsolete |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 10 |
| Resistance | 800mOhm |
| Subcategory | Multiplexer or Switches |
| Technology | CMOS |
| Terminal Position | DUAL |
| Terminal Form | NO LEAD |
| Peak Reflow Temperature (Cel) | 240 |
| Number of Functions | 2 |
| Supply Voltage | 3V |
| Terminal Pitch | 0.5mm |
| Reach Compliance Code | not_compliant |
| Time@Peak Reflow Temperature-Max (s) | 30 |
| Base Part Number | NLAS4684 |
| Output | SEPARATE OUTPUT |
| Pin Count | 10 |
| Qualification Status | Not Qualified |
| Operating Supply Voltage | 5V |
| Number of Channels | 1 |
| Number of Circuits | 2 |
| Max Supply Voltage | 5.5V |
| Min Supply Voltage | 1.8V |
| Operating Supply Current | 200nA |
| Turn On Delay Time | 50 ns |
| Supply Type | Single |
| Turn-Off Delay Time | 60 ns |
| -3db Bandwidth | 9.5MHz |
| On-State Resistance (Max) | 800mOhm |
| Multiplexer/Demultiplexer Circuit | 2:1 |
| Off-state Isolation-Nom | 65 dB |
| Current - Leakage (IS(off)) (Max) | 1μA |
| Channel Capacitance (CS(off), CD(off)) | 102pF 104pF |
| On-state Resistance Match-Nom | 0.06Ohm |
| Switch Circuit | SPDT |
| Switch Time (Ton, Toff) (Max) | 30ns, 30ns |
| Charge Injection | 15pC |
| Channel-to-Channel Matching (ΔRon) | 60m Ω |
| Crosstalk | -83dB @ 100kHz |
| Switching | BREAK-BEFORE-MAKE |
| Voltage - Supply, Single (V+) | 1.8V~5.5V |
| Height Seated (Max) | 1mm |
| Length | 3mm |
| RoHS Status | Non-RoHS Compliant |
| Lead Free | Contains Lead |
NLAS4684MNR2 Overview
Shipping overseas is convenient due to the electrical component's packing in 10-VFDFN Exposed Pad. High reliability is provided by advanced packaging method Tape & Reel (TR). Multiplexers like this are mounted in the Surface Mount position. Multiplexers and demultiplexers have a number of circuits 2:1. The operating temperature is extended to around -55°C~125°C TA. Total terminations are 10. Due to its 1 channels, the electrical component produces high-quality output. An 3V voltage supply should allow the electrical part to be turned on and run. There are 10 pins injected into the electronic part body. Multiplexers built on a SPDT switching circuit are built. This multiplexer is composed of 2 circuits. Look for analog switch ic variants by searching with NLAS4684. There is 800mOhm internal resistance in this digital multiplexer. Please refer to the datasheets for 10 pins functions. It is a typical Multiplexer or Switches analog multiplexer. A voltage higher than 5.5V should not normally be supplied to the switches. Single supply type digital switch with a low cost. A low voltage of 1.8V should be applied to the electronic component. In order to operate this switch device, it would need a current of 200nA. A voltage of 1.8V~5.5V is required for this switch device, which drains from a single voltage source. There are SEPARATE OUTPUT outputs on this analog switch ic. There is a voltage range of 5V operating voltages for the electrical part.
NLAS4684MNR2 Features
1 Channels
Switch Circuit: SPDT
200nA Supply Current
-3db Bandwidth: 9.5MHz
NLAS4684MNR2 Applications
There are a lot of ON Semiconductor NLAS4684MNR2 Analog Switches & Multiplexers ICs applications.
- Existing multiplexer applications (both fault-protected and nonfault-protected)
- RGB switches
- Audio and video switching
- SONET/SDH ADM
- Routers
- MP3 players
- Audio signal routing
- Avionics and Military Systems
- Digital cross connects (DSX-1)
- Communication systems