NLAS4501DTT1G
| Parameters | |
|---|---|
| Lifecycle Status | LAST SHIPMENTS (Last Updated: 4 days ago) |
| Mounting Type | Surface Mount |
| Package / Case | SOT-23-5 Thin, TSOT-23-5 |
| Surface Mount | YES |
| Number of Pins | 5 |
| Operating Temperature | -55°C~125°C TA |
| Packaging | Tape & Reel (TR) |
| Published | 2007 |
| JESD-609 Code | e3 |
| Pbfree Code | yes |
| Part Status | Obsolete |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 5 |
| Resistance | 25Ohm |
| Terminal Finish | Tin (Sn) |
| Subcategory | Multiplexer or Switches |
| Max Power Dissipation | 200mW |
| Technology | CMOS |
| Terminal Position | DUAL |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 260 |
| Number of Functions | 1 |
| Supply Voltage | 3V |
| Time@Peak Reflow Temperature-Max (s) | 40 |
| Base Part Number | NLAS4501 |
| Pin Count | 5 |
| Operating Supply Voltage | 5V |
| Number of Channels | 1 |
| Max Supply Voltage | 5.5V |
| Min Supply Voltage | 2V |
| Operating Supply Current | 1μA |
| Power Dissipation | 200mW |
| Throw Configuration | SPST |
| Turn On Delay Time | 14 ns |
| Halogen Free | Halogen Free |
| Supply Type | Single |
| Turn-Off Delay Time | 22 ns |
| -3db Bandwidth | 220MHz |
| On-State Resistance (Max) | 25Ohm |
| Multiplexer/Demultiplexer Circuit | 1:1 |
| Off-state Isolation-Nom | 93 dB |
| Current - Leakage (IS(off)) (Max) | 1nA |
| Channel Capacitance (CS(off), CD(off)) | 10pF 10pF |
| Switch Circuit | SPST - NO |
| Switch Time (Ton, Toff) (Max) | 9ns, 10ns |
| Charge Injection | 3pC |
| Voltage - Supply, Single (V+) | 2V~5.5V |
| Normal Position | NO |
| Height | 1mm |
| Length | 3mm |
| Width | 1.5mm |
| Radiation Hardening | No |
| REACH SVHC | No SVHC |
| RoHS Status | RoHS Compliant |
| Lead Free | Lead Free |
NLAS4501DTT1G Overview
Due to its SOT-23-5 Thin, TSOT-23-5 packaging, the electronic part is convenient for international shipping. The advanced packaging method Tape & Reel (TR) provides high reliability. Surface Mount is where this multiplexer is located. Multiplexers and demultiplexers have a ratio of 1:1. The operating temperature is extended to around -55°C~125°C TA. 5 terminations have been made so far. High-quality output is provided by the electronic component's 1 channels. When the electronic component is given a voltage of 3V, it should be turned on and run. A total of 5 pins are injected into the body of the electronic part. A SPST - NO switching circuit is used to build these analog multiplexers. Try searching with NLAS4501 if you're looking for variants. A 25Ohm internal resistance characterizes this multiplexer. The datasheets for the 5 pins explain the functions. This switch device is a typical Multiplexer or Switches. An abnormal situation would be for the switch device to be supplied with a voltage greater than 5.5V. Analog switch ics with Single supply type are cost-effective. A low voltage of 2V should be applied to the electronic component. For this multiplexer to operate, 1μA current would be sufficient. Analogue multiplexers require a 2V~5.5V voltage to drain from a single voltage supply. A voltage of 5V can be used to operate the electronic component.
NLAS4501DTT1G Features
1 Channels
Switch Circuit: SPST - NO
1μA Supply Current
-3db Bandwidth: 220MHz
NLAS4501DTT1G Applications
There are a lot of ON Semiconductor NLAS4501DTT1G Analog Switches & Multiplexers ICs applications.
- Industrial and process control systems
- MP3 players
- ISDN NT1/TA
- Microwave transmission systems
- Imaging
- Avionics
- Microprocessor controlled systems
- Existing multiplexer applications (both fault-protected and nonfault-protected)
- DSUs
- Audio and video signal routing