MM74HC74AMX
| Parameters | |
|---|---|
| Propagation Delay | 40 ns |
| Quiescent Current | 4μA |
| Turn On Delay Time | 12 ns |
| Family | HC/UH |
| Logic Function | AND, D-Type, Flip-Flop |
| Current - Output High, Low | 5.2mA 5.2mA |
| Max I(ol) | 0.004 A |
| Number of Bits per Element | 1 |
| Max Propagation Delay @ V, Max CL | 19ns @ 6V, 50pF |
| Trigger Type | Positive Edge |
| Input Capacitance | 5pF |
| Number of Output Lines | 1 |
| Clock Edge Trigger Type | Positive Edge |
| Height | 1.5mm |
| Length | 8.75mm |
| Width | 4mm |
| Radiation Hardening | No |
| REACH SVHC | No SVHC |
| RoHS Status | ROHS3 Compliant |
| Lead Free | Lead Free |
| Factory Lead Time | 4 Weeks |
| Lifecycle Status | ACTIVE (Last Updated: 2 days ago) |
| Contact Plating | Tin |
| Mount | Surface Mount |
| Mounting Type | Surface Mount |
| Package / Case | 14-SOIC (0.154, 3.90mm Width) |
| Number of Pins | 14 |
| Weight | 240.999296mg |
| Operating Temperature | -40°C~85°C TA |
| Packaging | Tape & Reel (TR) |
| Published | 1999 |
| Series | 74HC |
| JESD-609 Code | e4 |
| Pbfree Code | yes |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 14 |
| ECCN Code | EAR99 |
| Type | D-Type |
| Terminal Finish | Nickel/Palladium/Gold (Ni/Pd/Au) |
| Subcategory | FF/Latches |
| Packing Method | TR |
| Technology | CMOS |
| Voltage - Supply | 2V~6V |
| Terminal Position | DUAL |
| Terminal Form | GULL WING |
| Supply Voltage | 4.5V |
| Base Part Number | 74HC74 |
| Function | Set(Preset) and Reset |
| Output Type | Differential |
| Polarity | Non-Inverting |
| Number of Channels | 2 |
| Voltage | 5V |
| Load Capacitance | 50pF |
| Output Current | 25mA |
| Clock Frequency | 94MHz |
MM74HC74AMX Overview
14-SOIC (0.154, 3.90mm Width)is the packaging method. D flip flop is included in the Tape & Reel (TR)package. T flip flop uses Differentialas its output configuration. The trigger it is configured with uses Positive Edge. There is an electronic component mounted in the way of Surface Mount. A supply voltage of 2V~6V is required for operation. Temperature is set to -40°C~85°C TA. It is an electronic flip flop with the type D-Type. JK flip flop is a part of the 74HCseries of FPGAs. You should not exceed 94MHzin the output frequency of the device. Terminations are 14. D latch belongs to the 74HC74 family. A voltage of 4.5V is used to power it. Its input capacitance is 5pFfarads. A device of this type belongs to the family of HC/UH. In this case, the electronic component is mounted in the way of Surface Mount. With its 14pins, it is designed to work with most electronic flip flops. This device exhibits a clock edge trigger type of Positive Edge. It is included in FF/Latches. Compared to other similar T flip flops, this device offers reliable performance and is well suited for TR. This T flip flop features a maximum design flexibility due to its output current of 25mA. In order to operate, the chip has 1 output lines. In terms of quiescent current, it consumes 4μA . A total of 2 channels are available.
MM74HC74AMX Features
Tape & Reel (TR) package
74HC series
14 pins
MM74HC74AMX Applications
There are a lot of ON Semiconductor MM74HC74AMX Flip Flops applications.
- Divide a clock signal by 2 or 4
- Digital electronics systems
- Power down protection
- Frequency Dividers
- Shift Registers
- Control circuits
- Individual Asynchronous Resets
- Balanced 24 mA output drivers
- Latch
- Guaranteed simultaneous switching noise level