MM74HC273WM
| Parameters | |
|---|---|
| Factory Lead Time | 4 Weeks |
| Lifecycle Status | ACTIVE (Last Updated: 1 day ago) |
| Contact Plating | Tin |
| Mount | Surface Mount |
| Mounting Type | Surface Mount |
| Package / Case | 20-SOIC (0.295, 7.50mm Width) |
| Number of Pins | 20 |
| Weight | 801mg |
| Operating Temperature | -40°C~85°C TA |
| Packaging | Tube |
| Published | 2005 |
| Series | 74HC |
| JESD-609 Code | e3 |
| Pbfree Code | yes |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 20 |
| Termination | SMD/SMT |
| ECCN Code | EAR99 |
| Type | D-Type |
| Subcategory | FF/Latches |
| Technology | CMOS |
| Voltage - Supply | 2V~6V |
| Terminal Position | DUAL |
| Terminal Form | GULL WING |
| Supply Voltage | 4.5V |
| Base Part Number | 74HC273 |
| Function | Master Reset |
| Output Type | Non-Inverted |
| Number of Elements | 1 |
| Polarity | Non-Inverting |
| Supply Voltage-Max (Vsup) | 6V |
| Power Supplies | 2/6V |
| Supply Voltage-Min (Vsup) | 2V |
| Number of Channels | 8 |
| Load Capacitance | 50pF |
| Output Current | 5.2mA |
| Number of Bits | 8 |
| Clock Frequency | 78MHz |
| Propagation Delay | 27 ns |
| Quiescent Current | 8μA |
| Turn On Delay Time | 18 ns |
| Family | HC/UH |
| Logic Function | D-Type, Flip-Flop |
| Current - Output High, Low | 5.2mA 5.2mA |
| Max I(ol) | 0.004 A |
| Max Propagation Delay @ V, Max CL | 23ns @ 6V, 50pF |
| Trigger Type | Positive Edge |
| Input Capacitance | 7pF |
| Number of Output Lines | 8 |
| fmax-Min | 24 MHz |
| Clock Edge Trigger Type | Positive Edge |
| Height Seated (Max) | 2.642mm |
| Width | 7.5mm |
| Radiation Hardening | No |
| REACH SVHC | No SVHC |
| RoHS Status | ROHS3 Compliant |
| Lead Free | Lead Free |
MM74HC273WM Overview
20-SOIC (0.295, 7.50mm Width)is the way it is packaged. It is contained within the Tubepackage. As configured, the output uses Non-Inverted. In the configuration of the trigger, Positive Edgeis used. Surface Mountis in the way of this electric part. The JK flip flop operates with an input voltage of 2V~6V volts. The operating temperature is -40°C~85°C TA. This electronic flip flop is of type D-Type. It is a type of FPGA belonging to the 74HC series. A frequency of 78MHzshould be the maximum output frequency. A total of 1elements are contained within it. A total of 20 terminations have been made. Members of the 74HC273family make up this object. It is powered from a supply voltage of 4.5V. The input capacitance of this JK flip flopis 7pF farads. In terms of electronic devices, this device belongs to the HC/UHfamily of devices. A part of the electronic system is mounted in the way of Surface Mount. With its 20pins, it is designed to work with most electronic flip flops. A Positive Edgeclock edge trigger is used in this device. The part you are looking for is included in FF/Latches. The design is based on 8bits. It reaches the maximum supply voltage (Vsup) at 6V. Normal operation requires a supply voltage (Vsup) above 2V. There are 2/6V power supplies attached to it. As a result of its output current of 5.2mA, it is very flexible in terms of design. There are 8 output lines on it. It consumes 8μA of quiescent current without being affected by external factors. Currently, there are 8 channels available.
MM74HC273WM Features
Tube package
74HC series
20 pins
8 Bits
2/6V power supplies
MM74HC273WM Applications
There are a lot of ON Semiconductor MM74HC273WM Flip Flops applications.
- Latch-up performance
- Storage registers
- ESCC
- Reduced system switching noise
- 2 – Bit synchronous counter
- Asynchronous counter
- Frequency Dividers
- Synchronous counter
- Single Up Count-Control Line
- Load Control