MCP6021-I/P
| Parameters | |
|---|---|
| Factory Lead Time | 8 Weeks |
| Mount | Through Hole |
| Mounting Type | Through Hole |
| Package / Case | 8-DIP (0.300, 7.62mm) |
| Number of Pins | 5 |
| Operating Temperature | -40°C~85°C |
| Packaging | Tube |
| Published | 2006 |
| JESD-609 Code | e3 |
| Pbfree Code | yes |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | Not Applicable |
| Number of Terminations | 8 |
| ECCN Code | EAR99 |
| Terminal Finish | Matte Tin (Sn) |
| Subcategory | Operational Amplifier |
| Technology | CMOS |
| Terminal Position | DUAL |
| Number of Functions | 1 |
| Supply Voltage | 5V |
| Base Part Number | MCP6021 |
| Pin Count | 8 |
| JESD-30 Code | R-PDIP-T8 |
| Qualification Status | Not Qualified |
| Output Type | Rail-to-Rail |
| Number of Channels | 1 |
| Number of Circuits | 1 |
| Nominal Supply Current | 1mA |
| Output Current | 22mA |
| Min Input Voltage | 2.5V |
| Slew Rate | 7V/μs |
| Architecture | VOLTAGE-FEEDBACK |
| Amplifier Type | General Purpose |
| Common Mode Rejection Ratio | 70 dB |
| Current - Input Bias | 1pA |
| Max Input Voltage | 5.5V |
| Voltage - Supply, Single/Dual (±) | 2.5V~5.5V |
| Input Offset Voltage (Vos) | 500μV |
| Bandwidth | 10MHz |
| Unity Gain BW-Nom | 10000 kHz |
| Voltage Gain | 110dB |
| Power Supply Rejection Ratio (PSRR) | 74dB |
| Low-Offset | YES |
| Frequency Compensation | YES |
| Supply Voltage Limit-Max | 7V |
| Current - Output / Channel | 30mA |
| Low-Bias | YES |
| Micropower | NO |
| Max Frequency | 10kHz |
| Programmable Power | NO |
| Height | 4.953mm |
| Length | 10.16mm |
| Width | 7.112mm |
| REACH SVHC | No SVHC |
| RoHS Status | ROHS3 Compliant |
| Lead Free | Lead Free |
MCP6021-I/P Overview
It is packaged in an 8-DIP (0.300, 7.62mm)-case that protects the operational amplifiers from damage. A General Purpose-type buffer amplifier is shown here. A Tube case is used for delivering the op amp. During the past two weeks, there have been close to 8 terminations. A total of 8 pins are located on this board. I would like to remind you that this buffer op amp should be powered by an 5V battery. This particular linear amplifier is a type of Operational Amplifier device, to be precise. The buffer op amp includes 5 pins. Op amp rates 500μV as input offset voltage. Through Hole is the recommended mounting type for this linear amplifier. In terms of operating temperature, this instrumentation amplifier performs well at a temperature of about -40°C~85°C . Op amp is a member of the 110dB's 110dB family. There are 1 circuits on this op amp. There are a total of 1 channels available on the op amps. Buffer amplifier produces Rail-to-Rail signals, which is one of its many benefits.
MCP6021-I/P Features
8 Pins
supply voltage of 5V
110dB voltage gain
Output Type: Rail-to-Rail
MCP6021-I/P Applications
There are a lot of Microchip Technology MCP6021-I/P Instrumentational OP Amps applications.
- Information processing
- Automatic control
- Large motor controllers
- Multimedia playback equipment
- Proportional operation circuits
- Gaming industry
- Video data acquisition
- Polarized electrodes
- Blood pressure sensors
- single/dual op amp sum and difference circuits