MC74VHCT574ADW
| Parameters | |
|---|---|
| Mounting Type | Surface Mount |
| Package / Case | 20-SOIC (0.295, 7.50mm Width) |
| Surface Mount | YES |
| Operating Temperature | -40°C~85°C TA |
| Packaging | Tube |
| Series | 74VHCT |
| JESD-609 Code | e0 |
| Pbfree Code | no |
| Part Status | Obsolete |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 20 |
| Type | D-Type |
| Terminal Finish | TIN LEAD |
| Technology | CMOS |
| Voltage - Supply | 4.5V~5.5V |
| Terminal Position | DUAL |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 240 |
| Supply Voltage | 5V |
| Reach Compliance Code | unknown |
| Time@Peak Reflow Temperature-Max (s) | 30 |
| JESD-30 Code | R-PDSO-G20 |
| Function | Standard |
| Qualification Status | COMMERCIAL |
| Output Type | Tri-State, Non-Inverted |
| Number of Elements | 1 |
| Supply Voltage-Max (Vsup) | 5.5V |
| Supply Voltage-Min (Vsup) | 4.5V |
| Number of Ports | 2 |
| Clock Frequency | 130MHz |
| Family | AHCT/VHCT |
| Current - Quiescent (Iq) | 4μA |
| Output Characteristics | 3-STATE |
| Current - Output High, Low | 8mA 8mA |
| Output Polarity | TRUE |
| Number of Bits per Element | 8 |
| Max Propagation Delay @ V, Max CL | 10.4ns @ 5V, 50pF |
| Trigger Type | Positive Edge |
| Input Capacitance | 4pF |
| Height Seated (Max) | 2.65mm |
| Width | 7.5mm |
| RoHS Status | Non-RoHS Compliant |
MC74VHCT574ADW Overview
As a result, it is packaged as 20-SOIC (0.295, 7.50mm Width). The package Tubecontains it. There is a Tri-State, Non-Invertedoutput configured with it. It is configured with a trigger that uses a value of Positive Edge. Surface Mountis positioned in the way of this electronic part. Powered by a 4.5V~5.5Vvolt supply, it operates as follows. It is at -40°C~85°C TAdegrees Celsius that the system is operating. Logic flip flops of this type are classified as D-Type. JK flip flop belongs to the 74VHCTseries of FPGAs. This D flip flop should not have a frequency greater than 130MHz. The element count is 1 . It consumes 4μA of quiescent The number of terminations is 20. Power is supplied from a voltage of 5V volts. A JK flip flop with a 4pFfarad input capacitance is used here. An electronic device belonging to the family AHCT/VHCTcan be found here. It reaches 5.5Vwhen the maximum supply voltage (Vsup) is applied. The supply voltage (Vsup) should be maintained above 4.5V for normal operation. This flip flop has a total of 2ports.
MC74VHCT574ADW Features
Tube package
74VHCT series
MC74VHCT574ADW Applications
There are a lot of Rochester Electronics, LLC MC74VHCT574ADW Flip Flops applications.
- Latch-up performance
- Divide a clock signal by 2 or 4
- Count Modes
- Asynchronous counter
- Shift Registers
- Common Clocks
- Single Down Count-Control Line
- Data transfer
- Memory
- Functionally equivalent to the MC10/100EL29