MC74HCT273ADTR2
| Parameters | |
|---|---|
| Mount | Surface Mount |
| Mounting Type | Surface Mount |
| Package / Case | 20-TSSOP (0.173, 4.40mm Width) |
| Number of Pins | 20 |
| Operating Temperature | -55°C~125°C TA |
| Packaging | Tape & Reel (TR) |
| Published | 2011 |
| Series | 74HCT |
| JESD-609 Code | e4 |
| Pbfree Code | yes |
| Part Status | Obsolete |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 20 |
| Type | D-Type |
| Terminal Finish | Nickel/Palladium/Gold (Ni/Pd/Au) |
| Subcategory | FF/Latches |
| Packing Method | TAPE AND REEL |
| Technology | CMOS |
| Voltage - Supply | 4.5V~5.5V |
| Terminal Position | DUAL |
| Terminal Form | GULL WING |
| Supply Voltage | 5V |
| Terminal Pitch | 0.635mm |
| Base Part Number | 74HCT273 |
| Function | Reset |
| Qualification Status | Not Qualified |
| Output Type | Non-Inverted |
| Operating Supply Voltage | 5V |
| Number of Elements | 1 |
| Polarity | Non-Inverting |
| Power Supplies | 5V |
| Number of Circuits | 8 |
| Load Capacitance | 50pF |
| Clock Frequency | 30MHz |
| Propagation Delay | 25 ns |
| Turn On Delay Time | 25 ns |
| Logic Function | D-Type, Flip-Flop |
| Current - Quiescent (Iq) | 4μA |
| Current - Output High, Low | 4mA 4mA |
| Max I(ol) | 0.004 A |
| Max Propagation Delay @ V, Max CL | 25ns @ 5V, 50pF |
| Trigger Type | Positive Edge |
| Clock Edge Trigger Type | Positive Edge |
| RoHS Status | Non-RoHS Compliant |
| Lead Free | Contains Lead |
MC74HCT273ADTR2 Overview
The item is packaged in 20-TSSOP (0.173, 4.40mm Width)cases. As part of the package Tape & Reel (TR), it is embedded. In the configuration, Non-Invertedis used as the output. It is configured with a trigger that uses a value of Positive Edge. There is an electrical part that is mounted in the way of Surface Mount. The supply voltage is set to 4.5V~5.5V. Temperature is set to -55°C~125°C TA. D-Typedescribes this flip flop. In this case, it is a type of FPGA belonging to the 74HCT series. It should not exceed 30MHzin its output frequency. A total of 1 elements are present. There is 4μA quiescent consumption. There are 20 terminations,JK flip flop belongs to 74HCT273 family. It is powered by a voltage of 5V . It is mounted by the way of Surface Mount. The electronic flip flop is designed with pins 20. Its clock edge trigger type is Positive Edge. There is a FF/Latchesbase part number assigned to the RS flip flops. To achieve this superior flexibility, 8 circuits are used. As a result of its reliability, this D flip flop is ideally suited for TAPE AND REEL. A power supply of 5Vis required to operate it. If high efficiency is desired, the supply voltage should be kept at 5V.
MC74HCT273ADTR2 Features
Tape & Reel (TR) package
74HCT series
20 pins
5V power supplies
MC74HCT273ADTR2 Applications
There are a lot of ON Semiconductor MC74HCT273ADTR2 Flip Flops applications.
- Latch-up performance
- EMI reduction circuitry
- Bus hold
- Power down protection
- Asynchronous counter
- Reduced system switching noise
- Patented noise
- ESCC
- Single Up Count-Control Line
- Storage Registers