MC74ACT574DW
| Parameters | |
|---|---|
| Mount | Surface Mount |
| Mounting Type | Surface Mount |
| Package / Case | 20-SOIC (0.295, 7.50mm Width) |
| Number of Pins | 20 |
| Operating Temperature | -40°C~85°C TA |
| Packaging | Tube |
| Published | 2006 |
| Series | 74ACT |
| JESD-609 Code | e0 |
| Part Status | Obsolete |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 20 |
| Type | D-Type |
| Terminal Finish | Tin/Lead (Sn/Pb) |
| Subcategory | FF/Latches |
| Technology | CMOS |
| Voltage - Supply | 4.5V~5.5V |
| Terminal Position | DUAL |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 240 |
| Supply Voltage | 5V |
| Reach Compliance Code | not_compliant |
| Time@Peak Reflow Temperature-Max (s) | 30 |
| Base Part Number | 74ACT574 |
| Function | Standard |
| Qualification Status | Not Qualified |
| Output Type | Tri-State, Non-Inverted |
| Number of Elements | 1 |
| Polarity | Non-Inverting |
| Supply Voltage-Max (Vsup) | 5.5V |
| Power Supplies | 5V |
| Supply Voltage-Min (Vsup) | 4.5V |
| Load Capacitance | 50pF |
| Number of Ports | 2 |
| Number of Bits | 8 |
| Clock Frequency | 100MHz |
| Propagation Delay | 11 ns |
| Turn On Delay Time | 2.5 ns |
| Family | ACT |
| Logic Function | D-Type, Flip-Flop |
| Current - Quiescent (Iq) | 8μA |
| Current - Output High, Low | 24mA 24mA |
| Max I(ol) | 0.024 A |
| Max Propagation Delay @ V, Max CL | 11ns @ 5V, 50pF |
| Trigger Type | Positive Edge |
| Input Capacitance | 4.5pF |
| Number of Input Lines | 8 |
| Number of Output Lines | 3 |
| Clock Edge Trigger Type | Positive Edge |
| Height Seated (Max) | 2.65mm |
| Width | 7.5mm |
| RoHS Status | Non-RoHS Compliant |
| Lead Free | Contains Lead |
MC74ACT574DW Overview
20-SOIC (0.295, 7.50mm Width)is the way it is packaged. A package named Tubeincludes it. Currently, the output is configured to use Tri-State, Non-Inverted. It is configured with a trigger that uses a value of Positive Edge. Surface Mountis occupied by this electronic component. A voltage of 4.5V~5.5Vis used as the supply voltage. Temperature is set to -40°C~85°C TA. D-Typedescribes this flip flop. JK flip flop is a part of the 74ACTseries of FPGAs. Its output frequency should not exceed 100MHz Hz. In total, it contains 1 elements. During its operation, it consumes 8μA quiescent energy. There are 20 terminations,D latch belongs to the 74ACT574 family. The power supply voltage is 5V. This T flip flop has a capacitance of 4.5pF farads at the input. ACTis the family of this D flip flop. A part of the electronic system is mounted in the way of Surface Mount. As you can see from the design, it has pins with 20. It has a clock edge trigger type of Positive Edge. The part you are looking for is included in FF/Latches. An electronic part with 8bits has been designed. There is a 5.5Vmaximum supply voltage (Vsup). Normal operation requires a supply voltage (Vsup) above 4.5V. In order for the device to operate, it requires 5V power supplies. The D flip flop is embedded with 2ports. It operates with 3 output lines. As of now, there are 8input lines.
MC74ACT574DW Features
Tube package
74ACT series
20 pins
8 Bits
5V power supplies
MC74ACT574DW Applications
There are a lot of ON Semiconductor MC74ACT574DW Flip Flops applications.
- Patented noise
- Guaranteed simultaneous switching noise level
- Balanced 24 mA output drivers
- Instrumentation
- Data storage
- Communications
- Circuit Design
- Safety Clamp
- Bounce elimination switch
- CMOS Process