MC100EL51DTR2
| Parameters | |
|---|---|
| Mount | Surface Mount |
| Mounting Type | Surface Mount |
| Package / Case | 8-TSSOP, 8-MSOP (0.118, 3.00mm Width) |
| Operating Temperature | -40°C~85°C TA |
| Packaging | Tape & Reel (TR) |
| Published | 2008 |
| Series | 100EL |
| JESD-609 Code | e0 |
| Part Status | Obsolete |
| Moisture Sensitivity Level (MSL) | 3 (168 Hours) |
| Number of Terminations | 8 |
| Type | D-Type |
| Terminal Finish | Tin/Lead (Sn/Pb) |
| Additional Feature | NECL MODE: VCC = 0V WITH VEE = -4.2V TO -5.7V |
| Subcategory | FF/Latches |
| Packing Method | TAPE AND REEL |
| Technology | ECL |
| Voltage - Supply | -4.2V~-5.7V |
| Terminal Position | DUAL |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 240 |
| Supply Voltage | 5V |
| Terminal Pitch | 0.65mm |
| Reach Compliance Code | not_compliant |
| Time@Peak Reflow Temperature-Max (s) | 30 |
| Base Part Number | 100EL51 |
| JESD-30 Code | S-PDSO-G8 |
| Function | Reset |
| Qualification Status | Not Qualified |
| Output Type | Differential |
| Polarity | Non-Inverting |
| Supply Voltage-Max (Vsup) | 5.7V |
| Power Supplies | -4.5V |
| Supply Voltage-Min (Vsup) | 4.2V |
| Number of Circuits | 1 |
| Number of Bits | 1 |
| Clock Frequency | 2.8GHz |
| Propagation Delay | 565 ps |
| Turn On Delay Time | 475 ps |
| Logic Function | Flip-Flop |
| Current - Quiescent (Iq) | 29mA |
| Prop. Delay@Nom-Sup | 0.62 ns |
| Trigger Type | Positive, Negative |
| Power Supply Current-Max (ICC) | 36mA |
| fmax-Min | 2200 MHz |
| Clock Edge Trigger Type | Positive Edge |
| Length | 3mm |
| Width | 3mm |
| RoHS Status | Non-RoHS Compliant |
| Lead Free | Contains Lead |
MC100EL51DTR2 Overview
The item is packaged in 8-TSSOP, 8-MSOP (0.118, 3.00mm Width)cases. It is included in the package Tape & Reel (TR). Differentialis the output configured for it. The trigger it is configured with uses Positive, Negative. This electronic part is mounted in the way of Surface Mount. A voltage of -4.2V~-5.7Vis used as the supply voltage. It is at -40°C~85°C TAdegrees Celsius that the system is operating. This electronic flip flop is of type D-Type. FPGAs belonging to the 100ELseries contain this type of chip. It should not exceed 2.8GHzin its output frequency. T flip flop consumes 29mA quiescent energy. There have been 8 terminations. D latch belongs to the 100EL51 family. A voltage of 5V provides power to the D latch. This electronic part is mounted in the way of Surface Mount. This device's clock edge trigger type is Positive Edge. The part is included in FF/Latches. 1bits are used in its design. It reaches 5.7Vwhen the supply voltage is maximal (Vsup). Normally, the supply voltage (Vsup) should be kept above 4.2V. 1 circuits are used to achieve its superior flexibility. A reliable performance of this D flip flop makes it well suited for use in TAPE AND REEL. A power supply of -4.5Vis required to operate it. In addition, you can refer to the additinal NECL MODE: VCC = 0V WITH VEE = -4.2V TO -5.7V of the D latch.
MC100EL51DTR2 Features
Tape & Reel (TR) package
100EL series
1 Bits
-4.5V power supplies
MC100EL51DTR2 Applications
There are a lot of ON Semiconductor MC100EL51DTR2 Flip Flops applications.
- Instrumentation
- Common Clocks
- Safety Clamp
- Bus hold
- Single Up Count-Control Line
- Asynchronous counter
- Count Modes
- Clock pulse
- Reduced system switching noise
- Balanced Propagation Delays