MAX9019EKA+T
| Parameters | |
|---|---|
| Factory Lead Time | 6 Weeks |
| Contact Plating | Tin |
| Mount | Surface Mount |
| Mounting Type | Surface Mount |
| Package / Case | SOT-23-8 |
| Number of Pins | 8 |
| Operating Temperature | -40°C~85°C |
| Packaging | Tape & Reel (TR) |
| Published | 2012 |
| Series | Beyond-the-Rails™ |
| JESD-609 Code | e3 |
| Pbfree Code | yes |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 8 |
| ECCN Code | EAR99 |
| Type | General Purpose |
| Subcategory | Comparators |
| Max Power Dissipation | 727mW |
| Technology | BICMOS |
| Terminal Position | DUAL |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 260 |
| Number of Functions | 2 |
| Supply Voltage | 5V |
| Terminal Pitch | 0.65mm |
| Base Part Number | MAX9019 |
| Pin Count | 8 |
| Output Type | CMOS, Push-Pull, Rail-to-Rail |
| Number of Elements | 2 |
| Power Supplies | 5V |
| Nominal Supply Current | 1.7μA |
| Output Current | 50mA |
| Max Supply Current | 1.7μA |
| Propagation Delay | 28 μs |
| Quiescent Current | 2μA |
| Response Time | 28000 ns |
| Common Mode Rejection Ratio | 80 dB |
| Voltage - Supply, Single/Dual (±) | 1.8V~5.5V |
| Input Offset Voltage (Vos) | 5mV |
| Power Supply Rejection Ratio (PSRR) | 80dB |
| Supply Voltage Limit-Max | 6V |
| Max Input Current | 1nA |
| Dual Supply Voltage | 5.5V |
| Input Bias Current | 1nA |
| Current - Quiescent (Max) | 2μA |
| Voltage - Input Offset (Max) | 5mV @ 5V |
| Current - Input Bias (Max) | 0.001μA @ 5V |
| Hysteresis | 4mV |
| CMRR, PSRR (Typ) | 80dB PSRR |
| Height | 1.3mm |
| Length | 3mm |
| Width | 1.75mm |
| Radiation Hardening | No |
| REACH SVHC | Unknown |
| RoHS Status | ROHS3 Compliant |
| Lead Free | Lead Free |
MAX9019EKA+T Overview
In order to facilitate transportation, it is packaged in SOT-23-8 .There is a comparator of type CMOS, Push-Pull, Rail-to-Rail output on this device.The part is shipped by Tape & Reel (TR) .8 terminals are found on the comparator.Electronic comparator is a component of the Comparators family.Supplied by 5V voltage, the comparator can accomplish the many demanding tasks.Electronic comparator can be classified as a General Purpose chip.This element consists of 2 elements in total.The device includes 8 pins.The recommended mounting method is Surface Mount .In order to avoid malfunctions, the operating temperature should be set to -40°C~85°C .Electronic comparator has 8 pins.You can find more pin-to-pin solutions for your special requirements by searching MAX9019 .There is a quiescent current of 2μA in this comparator.The board has a Surface Mount for mounting on a PCB or any other board.For normal use of the device, the nominal supply current should be 1.7μA .If the current supply exceeds 1.7μA , the comparator could malfunction.This device requires 5V power supplies to operate.The maximal current your can input into the device is 1nA .In this case, the part is from the Beyond-the-Rails? comparator series.
MAX9019EKA+T Features
CMOS, Push-Pull, Rail-to-Rail output capability
General Purpose IC
Employing 2 elements
Operates under -40°C~85°C
Quiescent Current: 2μA
MAX9019EKA+T Applications
There are a lot of Maxim Integrated MAX9019EKA+T linear comparators applications.
- Hand-Held Electronics
- Window Comparators
- Set Top Boxes
- Wearable Devices
- Wide Range VCO; MOS Clock Timers
- Analog front end
- Ultra-Low Power Systems
- Power management
- Mobile Phones and Tablets
- Pulse, Squarewave, and Time Delay Generators