MAX4721EUA+T
| Parameters | |
|---|---|
| Factory Lead Time | 6 Weeks |
| Mount | Surface Mount |
| Mounting Type | Surface Mount |
| Package / Case | 8-TSSOP, 8-MSOP (0.118, 3.00mm Width) |
| Number of Pins | 8 |
| Operating Temperature | -40°C~85°C TA |
| Packaging | Tape & Reel (TR) |
| Published | 2002 |
| JESD-609 Code | e3 |
| Pbfree Code | yes |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 8 |
| ECCN Code | EAR99 |
| Resistance | 4.5Ohm |
| Terminal Finish | Matte Tin (Sn) |
| Max Power Dissipation | 362mW |
| Technology | BICMOS |
| Terminal Position | DUAL |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 260 |
| Number of Functions | 2 |
| Supply Voltage | 3V |
| Terminal Pitch | 0.65mm |
| Time@Peak Reflow Temperature-Max (s) | 30 |
| Base Part Number | MAX4721 |
| Pin Count | 8 |
| Operating Supply Voltage | 5V |
| Number of Channels | 1 |
| Number of Circuits | 2 |
| Max Supply Voltage | 5.5V |
| Min Supply Voltage | 1.8V |
| Operating Supply Current | 1μA |
| Max Supply Current | 1μA |
| Throw Configuration | SPST |
| Turn On Delay Time | 80 ns |
| Data Rate | 12 Mbps |
| Supply Type | Single |
| Turn-Off Delay Time | 40 ns |
| -3db Bandwidth | 300MHz |
| On-State Resistance (Max) | 4.5Ohm |
| Multiplexer/Demultiplexer Circuit | 1:1 |
| Off-state Isolation-Nom | 55 dB |
| Current - Leakage (IS(off)) (Max) | 500pA |
| Channel Capacitance (CS(off), CD(off)) | 9pF |
| On-state Resistance Match-Nom | 0.1Ohm |
| Switch Circuit | SPST - NO |
| Switch Time (Ton, Toff) (Max) | 80ns, 40ns |
| Charge Injection | 5pC |
| Channel-to-Channel Matching (ΔRon) | 100m Ω |
| Crosstalk | -110dB @ 1MHz |
| Voltage - Supply, Single (V+) | 1.8V~5.5V |
| Height Seated (Max) | 1.1mm |
| Length | 3mm |
| Radiation Hardening | No |
| RoHS Status | ROHS3 Compliant |
MAX4721EUA+T Overview
Shipping overseas is convenient due to the electrical component's packing in 8-TSSOP, 8-MSOP (0.118, 3.00mm Width). This high-reliability packaging method uses advanced packaging methods Tape & Reel (TR). The multiplexer is located in Surface Mount. Multiplexer and demultiplexer circuits have a number 1:1. The operating temperature is extended to around -40°C~85°C TA. There are 8 terminations totally. A high-quality output is provided by the electrical component's 1 channels. Turning on and running the electrical part should be easy with a 3V voltage supply. An electrical component of this type can be found in the 8 series. Circuits based on SPST - NO switching are used to construct these analog switch ics. The circuits in this analogue multiplexer number 2. Try searching with MAX4721 to find analog multiplexer variants. A 4.5Ohm internal resistance characterizes this multiplexer. To find out what the 8 pins do, please refer to the datasheets. An abnormal situation would be for the switch device to be supplied with a voltage greater than 5.5V. Analogue multiplexer with a Single supply type that is cost-effective. It is recommended to use 1.8V as the lowest voltage for the electrical part. This digital switch can be operated with a current of 1μA. An analogue multiplexer drains from a single voltage supply at 1.8V~5.5V. The analogue multiplexer may be damaged if voltage is greater than 1μA. It can operate from 5V operating voltages.
MAX4721EUA+T Features
1 Channels
Switch Circuit: SPST - NO
1μA Supply Current
-3db Bandwidth: 300MHz
MAX4721EUA+T Applications
There are a lot of Maxim Integrated MAX4721EUA+T Analog Switches & Multiplexers ICs applications.
- Data switching
- DSLAMs
- DSUs
- Cell phones
- Medical Instrumentation
- Industrial and process control systems
- Communications systems
- MP3 players
- Modems
- Video signal routing