MAX4660EUA+
| Parameters | |
|---|---|
| Factory Lead Time | 6 Weeks |
| Mounting Type | Surface Mount |
| Package / Case | 8-TSSOP, 8-MSOP (0.118, 3.00mm Width) Exposed Pad |
| Surface Mount | YES |
| Number of Pins | 8 |
| Operating Temperature | -40°C~85°C TA |
| Packaging | Tube |
| Published | 2007 |
| JESD-609 Code | e3 |
| Pbfree Code | yes |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 8 |
| ECCN Code | EAR99 |
| Terminal Finish | Matte Tin (Sn) |
| Subcategory | Multiplexer or Switches |
| Technology | CMOS |
| Terminal Position | DUAL |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 260 |
| Number of Functions | 1 |
| Supply Voltage | 15V |
| Terminal Pitch | 0.65mm |
| Time@Peak Reflow Temperature-Max (s) | 30 |
| Base Part Number | MAX4660 |
| Output | SEPARATE OUTPUT |
| Pin Count | 8 |
| Qualification Status | Not Qualified |
| Power Supplies | 9/40/+-4.5/+-20V |
| Number of Channels | 1 |
| Number of Circuits | 1 |
| Voltage - Supply, Single/Dual (±) | 9V~40V ±4.5V~20V |
| Bandwidth | 225MHz |
| Neg Supply Voltage-Nom (Vsup) | -15V |
| On-State Resistance (Max) | 25Ohm |
| Multiplexer/Demultiplexer Circuit | 2:1 |
| Off-state Isolation-Nom | 70 dB |
| Current - Leakage (IS(off)) (Max) | 1nA |
| Channel Capacitance (CS(off), CD(off)) | 6pF |
| On-state Resistance Match-Nom | 0.4Ohm |
| Switch Circuit | SPDT |
| Charge Injection | 1.5pC |
| Channel-to-Channel Matching (ΔRon) | 400m Ω |
| Crosstalk | -76dB @ 1MHz |
| Switching | BREAK-BEFORE-MAKE |
| Drain to Source Resistance | 25Ohm |
| Length | 3mm |
| RoHS Status | ROHS3 Compliant |
MAX4660EUA+ Overview
The electronic part can be shipped overseas conveniently because it is packaged in 8-TSSOP, 8-MSOP (0.118, 3.00mm Width) Exposed Pad. Advanced packaging method Tube is used to provide high reliability. In Surface Mount, you'll find this switch device. Multiplexer and demultiplexer circuits have a number 2:1. Increasing operating temperature to around -40°C~85°C TA. Total terminations are 8. As a result of its 1 channels, this electronic component provides high-quality output. With a 15V voltage supply, the electrical component should be turned on and run. An injection of 8 pins is performed into the body of the electrical component. SPDT switching circuits are used in these analog switch ics. It consists of 1 circuits. Try searching for MAX4660 variants of the analog switch ic. The datasheets for the 8 pins explain the functions. It is a typical Multiplexer or Switches analog multiplexer. A total of SEPARATE OUTPUT outputs are available on this analog switch ic. This switch operates within the bandwidth of 225MHz. A Drain to Source resistance of 25Ohm is shown for this electronic part.
MAX4660EUA+ Features
1 Channels
Switch Circuit: SPDT
Bandwidth: 225MHz
Drain-to-Source resistance: 25Ohm
MAX4660EUA+ Applications
There are a lot of Maxim Integrated MAX4660EUA+ Analog Switches & Multiplexers ICs applications.
- Remote Powered Equipment
- Audio and video signal routing
- SONET
- High speed data transmission line cards
- Short/Medium Loop: approximately 2000 ft. of 26 AWG and 5 REN loads
- Avionics
- Communications systems
- ISDN NT1/TA
- Relay Replacement
- Precision test equipment