MAX4646EUA
| Parameters | |
|---|---|
| Subcategory | Multiplexer or Switches |
| Max Power Dissipation | 571mW |
| Technology | CMOS |
| Terminal Position | DUAL |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 240 |
| Number of Functions | 1 |
| Supply Voltage | 3V |
| Terminal Pitch | 0.65mm |
| Time@Peak Reflow Temperature-Max (s) | 20 |
| Base Part Number | MAX4646 |
| Pin Count | 8 |
| Operating Supply Voltage | 5V |
| Number of Channels | 1 |
| Number of Circuits | 1 |
| Max Supply Voltage | 5.5V |
| Min Supply Voltage | 1.8V |
| Operating Supply Current | 100pA |
| Nominal Supply Current | 1μA |
| Max Supply Current | 1μA |
| Throw Configuration | SPST |
| Turn On Delay Time | 10 ns |
| Supply Type | Single |
| Turn-Off Delay Time | 15 ns |
| On-State Resistance (Max) | 2.5Ohm |
| Multiplexer/Demultiplexer Circuit | 1:1 |
| Off-state Isolation-Nom | 55 dB |
| Current - Leakage (IS(off)) (Max) | 250pA |
| Channel Capacitance (CS(off), CD(off)) | 17pF 17pF |
| Switch Circuit | SPST - NC |
| Switch Time (Ton, Toff) (Max) | 15ns, 10ns |
| Charge Injection | 5pC |
| Channel-to-Channel Matching (ΔRon) | 100m Ω |
| Switching | BREAK-BEFORE-MAKE |
| Voltage - Supply, Single (V+) | 1.8V~5V |
| Normal Position | NC |
| Length | 3mm |
| Width | 3mm |
| Radiation Hardening | No |
| RoHS Status | Non-RoHS Compliant |
| Lead Free | Contains Lead |
| Mount | Surface Mount |
| Mounting Type | Surface Mount |
| Package / Case | 8-TSSOP, 8-MSOP (0.118, 3.00mm Width) |
| Number of Pins | 8 |
| Operating Temperature | -40°C~85°C TA |
| Packaging | Tube |
| Published | 2004 |
| JESD-609 Code | e0 |
| Pbfree Code | no |
| Part Status | Obsolete |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 8 |
| ECCN Code | EAR99 |
| Resistance | 2.5Ohm |
MAX4646EUA Overview
As the electronic part is packed in 8-TSSOP, 8-MSOP (0.118, 3.00mm Width), international shipping is convenient. Advanced packaging method Tube is used to provide high reliability. Mounted in Surface Mount is this multiplexer. Multiplexer and demultiplexer circuits have a number 1:1. Increasing operating temperature to around -40°C~85°C TA. A total of 8 terminations have been recorded. By its 1 channels, the electronic component provides high-quality output. If the voltage supply is 3V volts, the electrical component should be turned on and run. A key feature of the 8 series is the inclusion of this electronic part as part of its design. Circuits based on SPST - NC switching are used to construct these analog switch ics. It consists of 1 circuits. Use MAX4646 to search for variants of the digital switches. Analog switches have 2.5Ohm internal resistance. For details about the functions of 8 pins, please refer to the datasheets. Multiplexer or Switches is a typical switch device. Users shouldn't supply more than 5.5V voltage to the switch device. Single supply type digital switch with a low cost. There should be 1.8V voltage fed to the electrical part below 1.8V. It would be sufficient to run this analogue multiplexer with 100pA current. This analogue multiplexer requires a voltage of 1.8V~5V when it drains from a single voltage supply. Putting voltage greater than 1μA on the multiplexer may cause damage. The electrical part can be operated at 5V voltage levels.
MAX4646EUA Features
1 Channels
Switch Circuit: SPST - NC
100pA Supply Current
MAX4646EUA Applications
There are a lot of Maxim Integrated MAX4646EUA Analog Switches & Multiplexers ICs applications.
- HDTV
- Mechanical reed relay replacement
- Battery Powered Instruments
- Fiber to the Home
- DVD-R
- DSLAMs
- Automatic test equipment
- Optical Applications
- Avionics
- T1/E1 Terminals