MAX4595EXK-T
| Parameters | |
|---|---|
| Packaging | Tape & Reel (TR) |
| Published | 2005 |
| JESD-609 Code | e0 |
| Pbfree Code | no |
| Part Status | Obsolete |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 5 |
| Resistance | 10Ohm |
| Subcategory | Multiplexer or Switches |
| Max Power Dissipation | 247mW |
| Technology | CMOS |
| Terminal Position | DUAL |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 240 |
| Number of Functions | 1 |
| Supply Voltage | 3V |
| Time@Peak Reflow Temperature-Max (s) | 20 |
| Base Part Number | MAX4595 |
| Pin Count | 5 |
| Number of Channels | 1 |
| Number of Circuits | 1 |
| Max Supply Voltage | 5.5V |
| Min Supply Voltage | 2V |
| Operating Supply Current | 1μA |
| Max Supply Current | 1μA |
| Number of Bits | 4 |
| Throw Configuration | SPST |
| Turn On Delay Time | 35 ns |
| Supply Type | Single |
| Turn-Off Delay Time | 40 ns |
| -3db Bandwidth | 300MHz |
| On-State Resistance (Max) | 10Ohm |
| Multiplexer/Demultiplexer Circuit | 1:1 |
| Off-state Isolation-Nom | 80 dB |
| Current - Leakage (IS(off)) (Max) | 500pA |
| Channel Capacitance (CS(off), CD(off)) | 8pF 8pF |
| Switch Circuit | SPST - NC |
| Switch Time (Ton, Toff) (Max) | 35ns, 40ns |
| Charge Injection | 2pC |
| Switching | MAKE-BEFORE-BREAK |
| Switch-off Time-Max | 60ns |
| Voltage - Supply, Single (V+) | 2V~5.5V |
| Normal Position | NC |
| Length | 2mm |
| Radiation Hardening | No |
| RoHS Status | Non-RoHS Compliant |
| Lead Free | Contains Lead |
| Mount | Surface Mount |
| Mounting Type | Surface Mount |
| Package / Case | 5-TSSOP, SC-70-5, SOT-353 |
| Number of Pins | 5 |
| Operating Temperature | -40°C~85°C TA |
MAX4595EXK-T Overview
Shipping overseas is convenient with the electronic component packed in 5-TSSOP, SC-70-5, SOT-353. High reliability is ensured by the advanced packaging method Tape & Reel (TR). It is mounted in the position Surface Mount. Multiplexers and demultiplexers have the same number of circuits 1:1. Around -40°C~85°C TA is the extended operating temperature. Total terminations are 5. This electronic part offers high-quality output due to its 1 channels. In the case of a voltage supply of 3V volts, the electrical part can be powered up and run. A key feature of the 5 series is the inclusion of this electronic part as part of its design. Based on SPST - NC switching circuits, these analog multiplexers work. Circuits number 1 make up this analogue multiplexer. Look for analog switch ic variants by searching with MAX4595. There is 10Ohm internal resistance in this digital multiplexer. Please refer to the datasheets for 5 pins functions. It is a typical Multiplexer or Switches analog multiplexer. It is normally recommended that users do not supply the multiplexer with voltages higher than 5.5V. Single supply type digital switch with a low cost. The lowest voltage the electronic part should receive is 2V. In order to operate this switch device, it would need a current of 1μA. A voltage of 2V~5.5V is required for this switch device, which drains from a single voltage source. Putting voltage greater than 1μA on the multiplexer may cause damage. Its conductivity is 4-bit.
MAX4595EXK-T Features
1 Channels
Switch Circuit: SPST - NC
1μA Supply Current
-3db Bandwidth: 300MHz
4-Bit
MAX4595EXK-T Applications
There are a lot of Maxim Integrated MAX4595EXK-T Analog Switches & Multiplexers ICs applications.
- Precision instrumentation
- Sample-and-hold systems
- Communications systems
- Data switching
- Residential Gateways, Home Gateway/Router
- Battery-powered systems
- FTTH
- Data Acquisition Systems
- Avionics test equipment
- Medical systems