MAX4543EKA-T
| Parameters | |
|---|---|
| Operating Temperature | -40°C~85°C TA |
| Packaging | Tape & Reel (TR) |
| Published | 2007 |
| JESD-609 Code | e4 |
| Pbfree Code | no |
| Part Status | Obsolete |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 8 |
| Resistance | 60Ohm |
| Terminal Finish | Nickel/Palladium/Gold (Ni/Pd/Au) |
| Subcategory | Multiplexer or Switches |
| Max Power Dissipation | 471mW |
| Technology | CMOS |
| Terminal Position | DUAL |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 240 |
| Number of Functions | 2 |
| Supply Voltage | 5V |
| Terminal Pitch | 0.65mm |
| Time@Peak Reflow Temperature-Max (s) | 20 |
| Base Part Number | MAX4543 |
| Output | SEPARATE OUTPUT |
| Pin Count | 8 |
| Operating Supply Voltage | 9V |
| Power Supplies | 3.3/5V |
| Number of Channels | 1 |
| Number of Circuits | 2 |
| Max Supply Voltage | 12V |
| Min Supply Voltage | 2.7V |
| Nominal Supply Current | 1μA |
| Max Supply Current | 1μA |
| Throw Configuration | SPST |
| Turn On Delay Time | 125 ns |
| Supply Type | Single |
| Turn-Off Delay Time | 400 ns |
| On-State Resistance (Max) | 60Ohm |
| Multiplexer/Demultiplexer Circuit | 1:1 |
| Off-state Isolation-Nom | 76 dB |
| Current - Leakage (IS(off)) (Max) | 100pA |
| Channel Capacitance (CS(off), CD(off)) | 8pF 8pF |
| On-state Resistance Match-Nom | 0.8Ohm |
| Switch Circuit | SPST - NO/NC |
| Switch Time (Ton, Toff) (Max) | 100ns, 75ns |
| Charge Injection | 1pC |
| Channel-to-Channel Matching (ΔRon) | 800m Ω |
| Crosstalk | -90dB @ 1MHz |
| Switching | BREAK-BEFORE-MAKE |
| Switch-on Time-Max | 100ns |
| Switch-off Time-Max | 75ns |
| Voltage - Supply, Single (V+) | 2.7V~12V |
| Height Seated (Max) | 1.45mm |
| Radiation Hardening | No |
| RoHS Status | Non-RoHS Compliant |
| Lead Free | Contains Lead |
| Mount | Surface Mount |
| Mounting Type | Surface Mount |
| Package / Case | SOT-23-8 |
| Number of Pins | 8 |
MAX4543EKA-T Overview
Shipping overseas is convenient with the electronic component packed in SOT-23-8. High reliability is ensured by the advanced packaging method Tape & Reel (TR). A switch device like this is mounted in Surface Mount. There is 1:1 ratio between the number of multiplexers and demultiplexers. Increasing operating temperature to around -40°C~85°C TA. 8 terminations have been made so far. By its 1 channels, the electronic component provides high-quality output. If the voltage supply is 5V volts, the electrical component should be turned on and run. As part of the design of the 8 series, this electronic part has been incorporated into the system. Circuits based on SPST - NO/NC switching are used to construct these analog switch ics. 2 circuits are used in this analogue multiplexer. Using the MAX4543 search parameter, you can discover variants of the switch. A 60Ohm internal resistance characterizes this multiplexer. Datasheets for functions of 8 pins are available. Multiplexer or Switches is a typical switch device. Users shouldn't supply more than 12V voltage to the switch device. Analog switch ics with Single supply type are cost-effective. It is recommended that the electrical component receives a voltage of 2.7V. Draining from a single voltage supply, this analog switch requires a voltage of 2.7V~12V. It may damage the digital multiplexer if the voltage is higher than 1μA. SEPARATE OUTPUT outputs are utilized by this digital multiplexer. The electronic component can function from 9V.
MAX4543EKA-T Features
1 Channels
Switch Circuit: SPST - NO/NC
MAX4543EKA-T Applications
There are a lot of Maxim Integrated MAX4543EKA-T Analog Switches & Multiplexers ICs applications.
- High speed data transmission line cards
- Battery Powered Instruments
- FTTH
- PBX interfaces
- Battery-powered systems
- Fault Tolerant Systems
- Video switching
- Sample-and-hold systems
- Medical Instrumentation
- Precision data acquisition