MAX4541ESA
| Parameters | |
|---|---|
| Mount | Surface Mount |
| Mounting Type | Surface Mount |
| Package / Case | 8-SOIC (0.154, 3.90mm Width) |
| Number of Pins | 8 |
| Operating Temperature | -40°C~85°C TA |
| Packaging | Tube |
| Published | 2007 |
| JESD-609 Code | e0 |
| Pbfree Code | no |
| Part Status | Obsolete |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 8 |
| ECCN Code | EAR99 |
| Resistance | 60Ohm |
| Subcategory | Multiplexer or Switches |
| Max Power Dissipation | 471mW |
| Technology | CMOS |
| Terminal Position | DUAL |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 240 |
| Number of Functions | 2 |
| Supply Voltage | 5V |
| Time@Peak Reflow Temperature-Max (s) | 20 |
| Base Part Number | MAX4541 |
| Output | SEPARATE OUTPUT |
| Pin Count | 8 |
| Operating Supply Voltage | 9V |
| Power Supplies | 3.3/5V |
| Number of Channels | 2 |
| Max Supply Voltage | 12V |
| Min Supply Voltage | 2.7V |
| Operating Supply Current | 100pA |
| Nominal Supply Current | 1μA |
| Max Supply Current | 1μA |
| Throw Configuration | SPST |
| Turn On Delay Time | 125 ns |
| Supply Type | Single |
| Turn-Off Delay Time | 400 ns |
| On-State Resistance (Max) | 60Ohm |
| Multiplexer/Demultiplexer Circuit | 1:1 |
| Off-state Isolation-Nom | 76 dB |
| Current - Leakage (IS(off)) (Max) | 100pA |
| Channel Capacitance (CS(off), CD(off)) | 8pF 8pF |
| On-state Resistance Match-Nom | 0.8Ohm |
| Switch Circuit | SPST - NO |
| Switch Time (Ton, Toff) (Max) | 100ns, 75ns |
| Charge Injection | 1pC |
| Channel-to-Channel Matching (ΔRon) | 800m Ω |
| Crosstalk | -90dB @ 1MHz |
| Switching | BREAK-BEFORE-MAKE |
| Switch-on Time-Max | 100ns |
| Switch-off Time-Max | 75ns |
| Voltage - Supply, Single (V+) | 2.7V~12V |
| Normal Position | NO |
| Height Seated (Max) | 1.75mm |
| Length | 4.9mm |
| Width | 3.9mm |
| Radiation Hardening | No |
| REACH SVHC | Unknown |
| RoHS Status | Non-RoHS Compliant |
| Lead Free | Contains Lead |
MAX4541ESA Overview
Shipping overseas is convenient with the electronic component packed in 8-SOIC (0.154, 3.90mm Width). A high level of reliability can be achieved through the use of an advanced packaging method Tube. It is mounted in the position Surface Mount. There is 1:1 ratio between the number of multiplexers and demultiplexers. Operation at a temperature around -40°C~85°C TA. A total of 8 terminations have been recorded. Due to its 2 channels, the electrical component produces high-quality output. With a 5V voltage supply, the electrical component should be turned on and run. The electronic part body is injected with 8 pins. Unlike digital switches, these are based on SPST - NO switching circuits. Use MAX4541 to search for variants of the digital switches. There is 60Ohm internal resistance in this digital multiplexer. The datasheets for the 8 pins explain the functions. There is a standard Multiplexer or Switches analogue multiplexer here. In a normalsituation, users should not supply the switches with voltage higher than 12V. Digital switch that provides Single power at a cost-effective price. 2.7V is the lowest voltage that should be fed to the electronic electronic part. This multiplexer would work with 100pA current. A voltage of 2.7V~12V is required to drain this analog switch from a single voltage supply. A voltage higher than 1μA may cause damage to the switch multiplexer. There are SEPARATE OUTPUT outputs on this analog switch ic. It can operate from 9V operating voltages.
MAX4541ESA Features
2 Channels
Switch Circuit: SPST - NO
100pA Supply Current
MAX4541ESA Applications
There are a lot of Maxim Integrated MAX4541ESA Analog Switches & Multiplexers ICs applications.
- Data switching
- CSU
- Signal routing between systems
- Communication systems
- Industrial control systems
- Mechanical reed relay replacement
- Ultrasound
- RGB switches
- Transmit
- 65 V DACs