MAX4502EXK-T
| Parameters | |
|---|---|
| Switch Time (Ton, Toff) (Max) | 75ns, 50ns |
| Charge Injection | 1pC |
| Switch-on Time-Max | 75ns |
| Switch-off Time-Max | 50ns |
| Voltage - Supply, Single (V+) | 2V~12V |
| Normal Position | NC |
| Length | 2mm |
| Radiation Hardening | No |
| RoHS Status | Non-RoHS Compliant |
| Lead Free | Contains Lead |
| Mount | Surface Mount |
| Mounting Type | Surface Mount |
| Package / Case | 5-TSSOP, SC-70-5, SOT-353 |
| Operating Temperature | -40°C~85°C TA |
| Packaging | Tape & Reel (TR) |
| Published | 1999 |
| JESD-609 Code | e0 |
| Pbfree Code | no |
| Part Status | Obsolete |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 5 |
| Resistance | 250Ohm |
| Subcategory | Multiplexer or Switches |
| Max Power Dissipation | 200mW |
| Technology | CMOS |
| Terminal Position | DUAL |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 240 |
| Number of Functions | 1 |
| Supply Voltage | 5V |
| Terminal Pitch | 0.65mm |
| Time@Peak Reflow Temperature-Max (s) | 20 |
| Base Part Number | MAX4502 |
| Pin Count | 5 |
| JESD-30 Code | R-PDSO-G5 |
| Operating Supply Voltage | 9V |
| Number of Channels | 1 |
| Number of Circuits | 1 |
| Max Supply Voltage | 12V |
| Min Supply Voltage | 2V |
| Operating Supply Current | 1μA |
| Max Supply Current | 1μA |
| Throw Configuration | SPST |
| Turn On Delay Time | 300 ns |
| Supply Type | Single |
| Turn-Off Delay Time | 125 ns |
| On-State Resistance (Max) | 250Ohm |
| Multiplexer/Demultiplexer Circuit | 1:1 |
| Off-state Isolation-Nom | 100 dB |
| Current - Leakage (IS(off)) (Max) | 1nA |
| Channel Capacitance (CS(off), CD(off)) | 3pF 3pF |
| Switch Circuit | SPST - NC |
MAX4502EXK-T Overview
Due to its 5-TSSOP, SC-70-5, SOT-353 packaging, the electronic part is convenient for international shipping. The advanced packaging method Tape & Reel (TR) provides high reliability. Mounted in Surface Mount is this multiplexer. There is 1:1 ratio between the number of multiplexers and demultiplexers. Around -40°C~85°C TA is the extended operating temperature. 5 terminations have been made so far. Due to its 1 channels, the electrical component produces high-quality output. An 5V voltage supply should allow the electrical part to be turned on and run. Into the electrical component body are injected 5 pins. Circuits based on SPST - NC switching are used to construct these analog switch ics. 1 circuits are used in this analogue multiplexer. Try searching for MAX4502 variants of the analog switch ic. This digital multiplexer has 250Ohm internal resistance. Multiplexer or Switches is a typical switch device. An abnormal situation would be for the switch device to be supplied with a voltage greater than 12V. Single supply type digital switch with a low cost. The lowest voltage fed to the electronic component should be 2V. This multiplexer would work with 1μA current. A voltage of 2V~12V is required for this switch device, which drains from a single voltage source. It may damage the digital multiplexer if the voltage is higher than 1μA. A voltage of 9V can be used to operate the electronic component.
MAX4502EXK-T Features
1 Channels
Switch Circuit: SPST - NC
1μA Supply Current
MAX4502EXK-T Applications
There are a lot of Maxim Integrated MAX4502EXK-T Analog Switches & Multiplexers ICs applications.
- DSUs
- SDH/SONET multiplexers
- Cable PC
- Imaging
- Data Acquisition Systems
- FTTH
- Modems
- DSLAMs
- Medical Instrumentation
- Microwave transmission systems