M74VHC1GT66DFT1G
| Parameters | |
|---|---|
| Number of Pins | 5 |
| Operating Temperature | -55°C~125°C TA |
| Packaging | Tape & Reel (TR) |
| Published | 2007 |
| JESD-609 Code | e3 |
| Pbfree Code | yes |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 5 |
| ECCN Code | EAR99 |
| Resistance | 40Ohm |
| Terminal Finish | Tin (Sn) |
| Subcategory | Multiplexer or Switches |
| Max Power Dissipation | 150mW |
| Technology | CMOS |
| Terminal Position | DUAL |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 260 |
| Number of Functions | 1 |
| Supply Voltage | 3V |
| Time@Peak Reflow Temperature-Max (s) | 40 |
| Base Part Number | M74VHC1GT66 |
| Pin Count | 5 |
| Operating Supply Voltage | 5V |
| Number of Channels | 1 |
| Max Supply Voltage | 5.5V |
| Min Supply Voltage | 2V |
| Power Dissipation | 150mW |
| Throw Configuration | SPST |
| Turn On Delay Time | 40 ns |
| Number of Inputs | 1 |
| Halogen Free | Halogen Free |
| Supply Type | Single |
| Turn-Off Delay Time | 40 ns |
| -3db Bandwidth | 180MHz |
| On-State Resistance (Max) | 40Ohm |
| Multiplexer/Demultiplexer Circuit | 1:1 |
| Off-state Isolation-Nom | 80 dB |
| Current - Leakage (IS(off)) (Max) | 100nA |
| Channel Capacitance (CS(off), CD(off)) | 10pF |
| Switch Circuit | SPST - NO |
| Switching | BREAK-BEFORE-MAKE |
| Voltage - Supply, Single (V+) | 2V~5.5V |
| Normal Position | NO |
| Height | 1mm |
| Length | 2.2mm |
| Width | 1.35mm |
| Radiation Hardening | No |
| REACH SVHC | No SVHC |
| RoHS Status | ROHS3 Compliant |
| Lead Free | Lead Free |
| Factory Lead Time | 10 Weeks |
| Lifecycle Status | ACTIVE (Last Updated: 6 days ago) |
| Mounting Type | Surface Mount |
| Package / Case | 5-TSSOP, SC-70-5, SOT-353 |
| Surface Mount | YES |
M74VHC1GT66DFT1G Overview
Packed in 5-TSSOP, SC-70-5, SOT-353, the electronic component is convenient for shipping overseas. High reliability is ensured by the advanced packaging method Tape & Reel (TR). It is mounted in the position Surface Mount. 1:1 is the number of circuits in the multiplexer and demultiplexer. The operating temperature is extended to around -55°C~125°C TA. Total terminations are 5. The electronic part delivers high-quality output through its 1 channels. A 3V voltage supply should turn on and run the electronic component. 5 pins are injected to the electronic part body. On the other hand, analog switches can be constructed using SPST - NO switching circuits. Search with M74VHC1GT66 if you are looking for analog multiplexer variants. It has an internal resistance of 40Ohm. For details about the functions of 5 pins, please refer to the datasheets. The analogue multiplexer in this example is a typical Multiplexer or Switches. It is normally recommended that users do not supply the multiplexer with voltages higher than 5.5V. Single supply type digital switch with a low cost. There should be 2V voltage fed to the electrical part below 2V. Using a single voltage supply, this switch device consumes 2V~5.5V volts. The electronic component can function from 5V. A 1 input needs to be operated.
M74VHC1GT66DFT1G Features
1 Channels
Switch Circuit: SPST - NO
-3db Bandwidth: 180MHz
M74VHC1GT66DFT1G Applications
There are a lot of ON Semiconductor M74VHC1GT66DFT1G Analog Switches & Multiplexers ICs applications.
- SDH
- Video signal routing
- High-Voltage
- RGB switches
- PBX interfaces
- Medical Instrumentation
- Isolation
- Fiber to the Home
- Short/Medium Loop: approximately 2000 ft. of 26 AWG and 5 REN loads
- Communications systems